05 Fakultät Informatik, Elektrotechnik und Informationstechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/6
Browse
19 results
Search Results
Item Open Access Impedance based temperature estimation of lithium ion cells using artificial neural networks(2021) Ströbel, Marco; Pross-Brakhage, Julia; Kopp, Mike; Birke, Kai PeterItem Open Access Pressure characteristics and chemical potentials of constrained LiFePO4/C6 cells(2018) Singer, Jan Patrick; Kropp, Timo; Kuehnemund, Martin; Birke, Kai PeterConstraining lithium-ion cells increases the cyclic lifetime. However, depending on an expected volume expansion during charge and discharge cycling, defining the optimal constraining pressure range is not straightforward. In this study, we investigate a lithium iron phosphate/graphite pouch cell at four initial constraining pressure levels. As a function of C-Rate, the thermodynamic principle of the non-monotonic pressure curve during full charge and discharge cycles is evaluated. Using the rubber balloon model to calculate the chemical potential of lithium iron phosphate and discussing the relationship between the chemical potential and pressure, we illustrate the pressure curve qualitatively. By applying differential pressure analysis, we evaluate the resulting pressure curves of a single graphite stage. Approaching a fundamental understanding of reduced cycling lifetime of full cells with unknown material composition, we allocate the stages and stage transitions of graphite as well as the phase transition of lithium iron phosphate. Local extreme values in the differential pressure analysis indicate phase and stage transitions. These values can identify critical operating conditions that should be considered for defining the optimum initial constraining pressure range.Item Open Access Non-uniform circumferential expansion of cylindrical Li-ion cells - the potato effect(2021) Hemmerling, Jessica; Guhathakurta, Jajnabalkya; Dettinger, Falk; Fill, Alexander; Birke, Kai PeterThis paper presents the non-uniform change in cell thickness of cylindrical Lithium (Li)-ion cells due to the change of State of Charge (SoC). Using optical measurement methods, with the aid of a laser light band micrometer, the expansion and contraction are determined over a complete charge and discharge cycle. The cell is rotated around its own axis by an angle of α=10° in each step, so that the different positions can be compared with each other over the circumference. The experimental data show that, contrary to the assumption based on the physical properties of electrode growth due to lithium intercalation in the graphite, the cell does not expand uniformly. Depending on the position and orientation of the cell coil, there are different zones of expansion and contraction. In order to confirm the non-uniform expansion around the circumference of the cell in 3D, X-ray computed tomography (CT) scans of the cells are performed at low and at high SoC. Comparison of the high resolution 3D reconstructed volumes clearly visualizes a sinusoidal pattern for non-uniform expansion. From the 3D volume, it can be confirmed that the thickness variation does not vary significantly over the height of the battery cell due to the observed mechanisms. However, a slight decrease in the volume change towards the poles of the battery cells due to the higher stiffness can be monitored.Item Open Access Cycling of double-layered graphite anodes in pouch-cells(2022) Müller, Daniel; Fill, Alexander; Birke, Kai PeterIncremental improvement to the current state-of-the-art lithium-ion technology, for example regarding the physical or electrochemical design, can bridge the gap until the next generation of cells are ready to take Li-ions place. Previously designed two-layered porosity-graded graphite anodes, together with LixNi0.6Mn0.2Co0.2O2 cathodes, were analysed in small pouch-cells with a capacity of around 1 Ah. For comparison, custom-made reference cells with the average properties of two-layered anodes were tested. Ten cells of each type were examined in total. Each cell pair, consisting of one double-layer and one single-layer (reference) cell, underwent the same test procedure. Besides regular charge and discharge cycles, electrochemical impedance spectroscopy, incremental capacity analysis, differential voltage analysis and current-pulse measurement are used to identify the differences in ageing behaviour between the two cell types. The results show similar behaviour and properties at beginning-of-life, but an astonishing improvement in capacity retention for the double-layer cells regardless of the cycling conditions. Additionally, the lifetime of the single-layer cells was strongly influenced by the cycling conditions, and the double-layer cells showed less difference in ageing behaviour.Item Open Access Optimization of disassembly strategies for electric vehicle batteries(2021) Baazouzi, Sabri; Rist, Felix Paul; Weeber, Max; Birke, Kai PeterVarious studies show that electrification, integrated into a circular economy, is crucial to reach sustainable mobility solutions. In this context, the circular use of electric vehicle batteries (EVBs) is particularly relevant because of the resource intensity during manufacturing. After reaching the end-of-life phase, EVBs can be subjected to various circular economy strategies, all of which require the previous disassembly. Today, disassembly is carried out manually and represents a bottleneck process. At the same time, extremely high return volumes have been forecast for the next few years, and manual disassembly is associated with safety risks. That is why automated disassembly is identified as being a key enabler of highly efficient circularity. However, several challenges need to be addressed to ensure secure, economic, and ecological disassembly processes. One of these is ensuring that optimal disassembly strategies are determined, considering the uncertainties during disassembly. This paper introduces our design for an adaptive disassembly planner with an integrated disassembly strategy optimizer. Furthermore, we present our optimization method for obtaining optimal disassembly strategies as a combination of three decisions: (1) the optimal disassembly sequence, (2) the optimal disassembly depth, and (3) the optimal circular economy strategy at the component level. Finally, we apply the proposed method to derive optimal disassembly strategies for one selected battery system for two condition scenarios. The results show that the optimization of disassembly strategies must also be used as a tool in the design phase of battery systems to boost the disassembly automation and thus contribute to achieving profitable circular economy solutions for EVBs.Item Open Access Influence of temperature and electrolyte composition on the performance of lithium metal anodes(2021) Boroujeni, Sanaz Momeni; Fill, Alexander; Ridder, Alexander; Birke, Kai PeterLithium metal anodes have again attracted widespread attention due to the continuously growing demand of cells with higher energy density. However, the lithium deposition mechanism and the affecting process of influencing factors, such as temperature, cycling current density, and electrolyte composition are not fully understood and require further investigation. In this article, the behavior of lithium metal anode at different temperatures (25, 40, and 60 ∘C), lithium salts, electrolyte concentrations (1 and 2 M), and the applied cell current (equivalent to 0.5 C, 1 C, and 2 C). is investigated. Two different salts were evaluated: lithium bis(fluorosulfonyl)imide (LiFSI) and lithium bis(trifluoromethanesul-fonyl)imide (LiTFSI). The cells at a medium temperature (40 ∘C) show the highest Coulombic efficiency (CE). However, shorter cycle life is observed compared to the experiments at room temperature (25 ∘C). Regardless of electrolyte type and C-rate, the higher temperature of 60 ∘C provides the worst Coulombic efficiency and cycle life among those at the examined temperatures. A higher C-rate has a positive effect on the stability over the cycle life of the lithium cells. The best performance in terms of long cycle life and relatively good Coulombic efficiency is achieved by fast charging the cell with high concentration LiFSI in 1,2-dimethoxyethane (DME) electrolyte at a temperature of 25 ∘C. The cell has an average Coulombic efficiency of 0.987 over 223 cycles. In addition to galvanostatic experiments, Electrochemical Impedance Spectroscopy (EIS) measurements were performed to study the evolution of the interface under different conditions during cycling.Item Open Access Comparison of aqueous- and non-aqueous-based binder polymers and the mixing ratios for Zn//MnO2 batteries with mildly acidic aqueous electrolytes(2021) Fitz, Oliver; Ingenhoven, Stefan; Bischoff, Christian; Gentischer, Harald; Birke, Kai Peter; Saracsan, Dragos; Biro, DanielConsidering the literature for aqueous rechargeable Zn//MnO2 batteries with acidic electrolytes using the doctor blade coating of the active material (AM), carbon black (CB), and binder polymer (BP) for the positive electrode fabrication, different binder types with (non-)aqueous solvents were introduced so far. Furthermore, in most of the cases, relatively high passive material (CB+BP) shares ~30 wt% were applied. The first part of this work focuses on different selected BPs: polyacrylonitrile (PAN), carboxymethyl cellulose (CMC), styrene butadiene rubber (SBR), cellulose acetate (CA), and nitrile butadiene rubber (NBR). They were used together with (non-)aqueous solvents: DI-water, methyl ethyl ketone (MEK), and dimethyl sulfoxide (DMSO). By performing mechanical, electrochemical and optical characterizations, a better overall performance of the BPs using aqueous solvents was found in aqueous 2 M ZnSO4 + 0.1 M MnSO4 electrolyte (i.e., BP LA133: 150 mAh·g-1 and 189 mWh·g-1 @ 160 mA·g-1). The second part focuses on the mixing ratio of the electrode components, aiming at the decrease of the commonly used passive material share of ~30 wt% for an industrial-oriented electrode fabrication, while still maintaining the electrochemical performance. Here, the absolute CB share and the CB/BP ratio are found to be important parameters for an application-oriented electrode fabrication (i.e., high energy/power applications).Item Open Access The influence of micro-structured anode current collectors in combination with highly concentrated electrolyte on the Coulombic efficiency of in-situ deposited Li-metal electrodes with different counter electrodes(2020) Heim, Fabian; Kreher, Tina; Birke, Kai PeterThis paper compares and combines two common methods to improve the cycle performance of lithium metal (Li) electrodes. One technique is to establish a micro-structured current collector by chemical separation of a copper/zinc alloy. Furthermore, the use of a highly concentrated ether-based electrolyte is applied as a second approach for improving the cycling behavior. The influence of the two measures compared with a planar current collector and a 1 M concentrated carbonate-based electrolyte, as well as the combination of the methods, are investigated in test cells both with Li and lithium nickel cobalt manganese oxide (NCM) as counter electrodes. In all cases Li is in-situ plated onto the micro-structured current collectors respectively a planar copper foil without presence of any excess Li before first deposition. In experiments with Li counter electrodes, the effect of a structured current collector is not visible whereas the influence of the electrolyte can be observed. With NCM counter electrodes and carbonate-based electrolyte structured current collectors can improve Coulombic efficiency. The confirmation of this outcome in experiments with highly concentrated ether-based electrolyte is challenging due to high deviations. However, these results indicate, that improvements in Coulombic efficiency achieved by structuring the current collector’s surface and using ether-based electrolyte do not necessarily add up, if both methods are combined in one cell.Item Open Access Feasible energy density pushes of Li-metal vs. Li-ion cells(2021) Karabelli, Duygu; Birke, Kai PeterLi-metal batteries are attracting a lot of attention nowadays. However, they are merely an attempt to enhance energy densities by employing a negative Li-metal electrode. Usually, when a Li-metal cell is charged, a certain amount of sacrificial lithium must be added, because irreversible losses per cycle add up much more unfavourably compared to conventional Li-ion cells. When liquid electrolytes instead of solid ones are used, additional electrolyte must also be added because both the lithium of the positive electrode and the liquid electrolyte are consumed during each cycle. Solid electrolytes may present a clever solution to the issue of saving sacrificial lithium and electrolyte, but their additional intrinsic weight and volume must be considered. This poses the important question of if and how much energy density can be gained in realistic scenarios if a switch from Li-ion to rechargeable Li-metal cells is anticipated. This paper calculates various scenarios assuming typical losses per cycle and reveals future e-mobility as a potential application of Li-metal cells. The paper discusses the trade-off if, considering only the push for energy density, liquid electrolytes can become a feasible option in large Li-metal batteries vs. the solid-state approach. This also includes the important aspect of cost.Item Open Access Revealing the local pH value changes of acidic aqueous zinc ion batteries with a manganese dioxide electrode during cycling(2020) Bischoff, Christian Friedrich; Fitz, Oliver Sebastian; Burns, Jordan; Bauer, Manuel; Gentischer, Harald; Birke, Kai Peter; Henning, Hans-Martin; Biro, DanielThe research on aqueous zinc ion batteries (AZIB) is getting more attention as the energy transition continues to develop and the need for inexpensive and safe stationary storage batteries is growing. As the detailed reaction mechanisms are not conclusively revealed, we want to take an alternative approach to investigate the importance of pH value changes during cycling. By adding a pH-indicator to the electrolyte (2 M ZnSO4 + 0.1 M MnSO4), the local pH-value change during operation is visualized in operando. The overall pH value was found to increase during cycling whereas a major temporary pH drop in close proximity of the manganese dioxide electrode surface occurs. Additionally, this pH value change was quantified locally by in operando measurements with a pH micro electrode. Different electrolyte compositions with additives (sodium dodecyl sulfate (SDS), sulfuric acid (H2SO4)) and operation voltages were tested. The pH-potential-diagrams of manganese and zinc reveal pH value and potential limits, leading to active material dissolution at lower pH values and oxygen gas evolution at higher potentials >1.7 V. The procedure of combining a pH indicator, pH microelectrode measurements and pH-potential diagrams can be seen as an appropriate method to determine the recommendable working window of aqueous batteries.