05 Fakultät Informatik, Elektrotechnik und Informationstechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/6
Browse
239 results
Search Results
Item Open Access Modeling and experimental investigation of the interaction between pressure-dependent aging and pressure development due to the aging of lithium-ion cells(2023) Avdyli, Arber; Fill, Alexander; Birke, Kai PeterIn order to meet the increasing demands of the battery in terms of range, safety and performance, it is necessary to ensure optimal operation conditions of a lithium-ion cell. In this thesis, the influence of mechanical boundary conditions on the cell is investigated theoretically and experimentally. First, fundamental equations are derived that lead to coupled models that can be parameterized based on specific cell measurements and predict the pressure evolution due to capacity aging and vice versa. The model is used to derive optimal operating points of the cell, which can be considered in the module design.Item Open Access A dual‐layered anode buffer layer structure for all solid‐state batteries(2024) Lu, Yushi; Chang, Hansen Michael; Birke, Kai PeterOver the past few decades, lithium‐ion batteries have garnered considerable attention, especially for their use in electric vehicles (EVs). In recent years, solid‐state batteries have become increasingly popular due to their excellent safety features and potential for high energy density. However, solid‐state batteries with lithium metal anodes present challenges in terms of electrochemical reactivity and cost. To address these challenges, alternative anode systems such as the “anode‐free” approach are being explored. In this study, we introduced a dual‐layered anode comprising a primary layer of physically vapor‐deposited zinc and a secondary layer of carbon black, focusing on investigating the influence of varying thicknesses of the lithiophilic zinc layer on cell cycling performance. Among the three different zinc thicknesses chosen for this purpose - categorized as thin (286 nm), medium (1.802 μm), and thick (6.519 μm) - the dual‐layered anode buffer layer was analyzed in a single‐layer full pouch cell. An in‐depth investigation into the lithium‐zinc alloying behavior was conducted through post‐mortem analysis. From the results, we found that the combination of the zinc layer with the carbon black layer improved cell cycling performance in terms of discharge capacity retention compared to a single layer of either zinc or carbon black. The cycling performance of this dual‐layered anode could be further enhanced by optimizing the zinc layer thickness, likely due to the irreversible alloying step of zinc and lithium. Among the various thicknesses evaluated, the thin zinc layer (286 nm) combined with the carbon black layer demonstrated the most promising cycling performance in all solid‐state batteries.Item Open Access Surface charge density and induced currents by self-charging sliding drops(2024) Bista, Pravash; Ratschow, Aaron D.; Stetten, Amy Z.; Butt, Hans-Jürgen; Weber, Stefan A. L.Spontaneous charge separation in drops sliding over a hydrophobized insulator surface is a well-known phenomenon and lots of efforts have been made to utilize this effect for energy harvesting. For maximizing the efficiency of such devices, a comprehensive understanding of the dewetted surface charge would be required to quantitatively predict the electric current signals, in particular for drop sequences. Here, we use a method based on mirror charge detection to locally measure the surface charge density after drops move over a hydrophobic surface. For this purpose, we position a metal electrode beneath the hydrophobic substrate to measure the capacitive current induced by the moving drop. Furthermore, we investigate drop-induced charging on different dielectric surfaces together with the surface neutralization processes. The surface neutralizes over a characteristic time, which is influenced by the substrate and the surrounding environment. We present an analytical model that describes the slide electrification using measurable parameters such as the surface charge density and its neutralization time. Understanding the model parameters and refining them will enable a targeted optimization of the efficiency in solid–liquid charge separation.Item Open Access A comprehensive model and experimental investigation of venting dynamics and mass loss in lithium-ion batteries under a thermal runaway(2025) Chen, Ai; Sahin, Resul; Ströbel, Marco; Kottke, Thomas; Hecker, Stefan; Fill, AlexanderThermal runaway (TR) has become a critical safety concern with the widespread use of lithium-ion batteries (LIBs) as an energy storage solution to meet the growing global energy demand. This issue has become a significant barrier to the expansion of LIB technologies. Addressing the urgent need for safer LIBs, this study developed a comprehensive model to simulate TR in cylindrical 18650 nickel cobalt manganese (NMC) LIBs. By incorporating experiments with LG ® -INR18650-MJ1 cells, the model specifically aimed to accurately predict critical TR parameters, including temperature evolution, internal pressure changes, venting phases, and mass loss dynamics. The simulation closely correlated with experimental outcomes, particularly in replicating double venting mechanisms, gas generation, and the characteristics of mass loss observed during TR events. This study confirmed the feasibility of assuming proportional relationships between gas generation and the cell capacity and between the mass loss from solid particle ejection and the total mass loss, thereby simplifying the modeling of both gas generation and mass loss behaviors in LIBs under TR. Conclusively, the findings advanced the understanding of TR mechanisms in LIBs, providing a solid foundation for future research aimed at mitigating risks and promoting the safe integration of LIBs into sustainable energy solutions.Item Open Access ILP-based resource optimization realized by quantum annealing for optical wide-area communication networks : a framework for solving combinatorial problems of a real-world application by quantum annealing(2024) Witt, Arthur; Kim, Jangho; Körber, Christopher; Luu, ThomasResource allocation of wide-area internet networks is inherently a combinatorial optimization problem that if solved quickly, could provide near real-time adaptive control of internet-protocol traffic ensuring increased network efficacy and robustness, while minimizing energy requirements coming from power-hungry transceivers. In recent works we demonstrated how such a problem could be cast as a quadratic unconstrained binary optimization (QUBO) problem that can be embedded onto the D-Wave Advantage™ quantum annealer system, demonstrating proof of principle. Our initial studies left open the possibility for improvement of D-Wave solutions via judicious choices of system run parameters. Here we report on our investigations for optimizing these system parameters, and how we incorporate machine learning (ML) techniques to further improve on the quality of solutions. In particular, we use the Hamming distance to investigate correlations between various system-run parameters and solution vectors. We then apply a decision tree neural network (NN) to learn these correlations, with the goal of using the neural network to provide further guesses to solution vectors. We successfully implement this NN in a simple integer linear programming (ILP) example, demonstrating how the NN can fully map out the solution space that was not captured by D-Wave. We find, however, for the 3-node network problem the NN is not able to enhance the quality of space of solutions.Item Open Access SalChartQA: question-driven saliency on information visualisations(2024) Wang, Yao; Wang, Weitian; Abdelhafez, Abdullah; Elfares, Mayar; Hu, Zhiming; Bâce, Mihai; Bulling, AndreasUnderstanding the link between visual attention and user’s needs when visually exploring information visualisations is under-explored due to a lack of large and diverse datasets to facilitate these analyses. To fill this gap, we introduce SalChartQA - a novel crowd-sourced dataset that uses the BubbleView interface as a proxy for human gaze and a question-answering (QA) paradigm to induce different information needs in users. SalChartQA contains 74,340 answers to 6,000 questions on 3,000 visualisations. Informed by our analyses demonstrating the tight correlation between the question and visual saliency, we propose the first computational method to predict question-driven saliency on information visualisations. Our method outperforms state-of-the-art saliency models, improving several metrics, such as the correlation coefficient and the Kullback-Leibler divergence. These results show the importance of information needs for shaping attention behaviour and paving the way for new applications, such as task-driven optimisation of visualisations or explainable AI in chart question-answering.Item Open Access Sharp MIR plasmonic modes in gratings made of heavily doped pulsed laser-melted Ge1-xSnx(2023) Berkmann, Fritz; Steuer, Oliver; Ganss, Fabian; Prucnal, Slawomir; Schwarz, Daniel; Fischer, Inga Anita; Schulze, JörgItem Open Access Optimal transistor dimensioning in T-type topology for reduced quasi-2-level switching loss(2025) Söllner, Adrian; Jie, Chengcong; Mönch, StefanA quasi-2-level switching T-type topology reduces hard-switching loss compared to half-bridges, but requires more semiconductor area. This work shows that the middle transistor can be dimensioned smaller than the high/low-side transistors, which further reduces both the switch node capacitance and switching loss. The paper also presents a scalable transistor model, which is used in simulations of inductive-load hard-switching to determine switching losses and reveal a loss-optimal transistor dimensioning. Furthermore a double pulse setup (600 V-rated GaN HEMTs in a T-type topology) with 2 ground referenced shunts is proposed to determine switching energy of middle and low side transistors simultaneously. To verify the concept of loss-optimal transistor dimensioning in Q2L T-type topology, switching energy was measured at 200 V and 1 A, with the middle transistors area reduced by half compared to high/low side, resulting in a measured reduction from 4.44 µJ to 2.18 µJ (-51%) which is similar to the simulated reduction (2.39 µJ to 1.43 µJ, -40%). This method allows reduction of Q2L switching-loss with optimal transistor area and can be used for a wide range of applications.Item Open Access Knowledge graphs in the digital twin : a systematic literature review about the combination of semantic technologies and simulation in industrial automation(2024) Listl, Franz; Dittler, Daniel; Hildebrandt, Gary; Stegmaier, Valentin; Jazdi, Nasser; Weyrich, MichaelItem Open Access Load-flow-based calculation of initial short-circuit currents for converter-based power system(2025) Deepak, Deepak; Oetoyo, Anisatur Rizqi; Rudion, Krzysztof; John, Christoph; Abele, HansShort-circuit current is a key characteristic value for synchronous generator-based power systems. It is employed for different applications during the planning and operation phases. The proportion of converter-interfaced units is increasing in order to integrate more renewable energy sources into the system. These units have different fault current characteristics due to their physical properties and operation strategies. Consequently, the network’s short-circuit current profile is changing, both in terms of magnitude and injection time. Therefore, accurately estimating fault currents is crucial for reliable power system planning and operation. Traditionally, two calculation methods are employed: the equivalent voltage source (IEC 60909/VDE 0102) and the superimposition (complete) method. In this work, the assumptions, simplifications, and limitations from both types of methods are addressed. As a result, a new load-flow-based method is presented, improving the static modeling of generating units and the accuracy in the estimation of short-circuit currents. The method is tested for mixed generation types comprising of synchronous generators, and grid-following (current source) and grid-forming (voltage source before and current source after the current limit) converters. All methods are compared against detailed time-domain RMS simulations using a modified IEEE-39 bus system and a real network from ENTSO-E. It is shown that the proposed method provides the best accuracy in the calculation of initial short-circuit currents for converter-based power systems.