05 Fakultät Informatik, Elektrotechnik und Informationstechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/6
Browse
210 results
Search Results
Item Open Access Modeling and experimental investigation of the interaction between pressure-dependent aging and pressure development due to the aging of lithium-ion cells(2023) Avdyli, Arber; Fill, Alexander; Birke, Kai PeterIn order to meet the increasing demands of the battery in terms of range, safety and performance, it is necessary to ensure optimal operation conditions of a lithium-ion cell. In this thesis, the influence of mechanical boundary conditions on the cell is investigated theoretically and experimentally. First, fundamental equations are derived that lead to coupled models that can be parameterized based on specific cell measurements and predict the pressure evolution due to capacity aging and vice versa. The model is used to derive optimal operating points of the cell, which can be considered in the module design.Item Open Access Effiziente Synthese konsistenter Graphen und ihre Anwendung in der Lokalisierung akustischer Quellen(2015) Kreißig, Martin; Yang, Bin (Prof. Dr.-Ing.)In dieser Arbeit wird das Problem der simultanen, akustischen Mehrquellenlokalisierung in echobehafteten Umgebungen genauer betrachtet und daran beispielhaft die Anwendungsmöglichkeit der Synthese konsistenter Graphen gezeigt und analysiert. Dafür werden die Grundlagen der akustischen Lokalisierung eingeführt und unterschiedliche Ansätze vorgestellt. Im Besonderen werden die laufzeitdifferenzbasierten Lokalisierungsverfahren betrachtet, die das Problem der uneindeutigen Zuweisung der Laufzeitdifferenzen zu den Quellen haben. Anhand dieses konkreten Anwendungsbeispiels der Lokalisierung wird die Problematik auf ein graphentheoretisches Problem abstrahiert. Deshalb werden zunächst die graphentheoretischen Grundlagen und bereits bekannte Algorithmen, wie die Tiefen- und Breitensuche eingeführt, die beide einen aufspannenden Baum suchen. Der aufspannende Baum ist notwendig, um die Menge der fundamentalen Maschen zu bestimmen. Die Synthese konsistenter Graphen erfolgt durch das Zusammenführen der konsistenten fundamentalen Maschen. Dabei unterscheidet man folgende Vorgehensweisen: die Synthese voll konsistenter Graphen, die jeder Kante des Eingangsgraphen ein konsistentes Kantengewicht zuweisen und die Synthese partiell konsistenter Graphen, die nur eine Teilmenge von Kanten beinhalten. Beide Vorgehensweisen basieren auf den konsistenten fundamentalen Maschen, welche die Nullsummenbedingung erfüllen. Die Synthese voll konsistenter Graphen wird über ein Backtracking-Verfahren realisiert. Die Synthese partiell konsistenter Graphen wird aus dem Kompatibilitäts-Konflikt-Graph abgeleitet, der ein neuer Typus von Graph ist und die drei unterschiedlichen Zustände zwischen den konsistenten fundamentalen Maschen beschreibt: 1) zwei konsistente Maschen haben keine gemeinsame Kanten, 2) zwei konsistente Maschen haben gemeinsame Kanten und identische Kantengewichte (kompatibel) und 3) zwei konsistente Maschen haben gemeinsame Kanten und unterschiedliche Kantengewichte (Konflikt). Um alle möglichen, partiell konsistenten Graphen zu synthetisieren, wird der neue Algorithmus CCGsearch eingeführt und auf Vollständigkeit bewiesen. Die Berechnungskomplexitäten der beiden Syntheseverfahren werden sowohl analytisch hergeleitet als auch durch Simulationen verifiziert.Item Open Access Surface charge density and induced currents by self-charging sliding drops(2024) Bista, Pravash; Ratschow, Aaron D.; Stetten, Amy Z.; Butt, Hans-Jürgen; Weber, Stefan A. L.Spontaneous charge separation in drops sliding over a hydrophobized insulator surface is a well-known phenomenon and lots of efforts have been made to utilize this effect for energy harvesting. For maximizing the efficiency of such devices, a comprehensive understanding of the dewetted surface charge would be required to quantitatively predict the electric current signals, in particular for drop sequences. Here, we use a method based on mirror charge detection to locally measure the surface charge density after drops move over a hydrophobic surface. For this purpose, we position a metal electrode beneath the hydrophobic substrate to measure the capacitive current induced by the moving drop. Furthermore, we investigate drop-induced charging on different dielectric surfaces together with the surface neutralization processes. The surface neutralizes over a characteristic time, which is influenced by the substrate and the surrounding environment. We present an analytical model that describes the slide electrification using measurable parameters such as the surface charge density and its neutralization time. Understanding the model parameters and refining them will enable a targeted optimization of the efficiency in solid–liquid charge separation.Item Open Access Active electronic loads for radiometric calibration(2017) Weissbrodt, Ernst; Kallfass, Ingmar (Prof. Dr.)Although radiometer systems are widely applied in very different fields, they all have one important requirement in common: They require a thorough radiometric calibration. Various conventional calibration references are well established, but their bulkiness, high power consumption, and complexity are limiting the expanding fields of application. Since novel industrial applications such as passive millimeter-wave imaging emerge, the requirements for calibration references have increased drastically. But also in scientific fields like radio astronomy, cosmology or environmental monitoring, modern remote sensing radiometers do not rely only on conventional references anymore. In this work, millimeter-wave monolithic integrated circuits (MMICs) based on metamorphic high electron mobility transistors (mHEMT) were designed to be used as active electronic loads for radiometric calibration. These novel references have not only the outstanding property, that they can be directly integrated on chip-level into the radiometer front-end, but also, that they can exhibit cold as well as hot reference noise temperatures. Since this is achieved without any physical cooling or heating, the power consumption is notably reduced. By monolithic integration of field effect transistor (FET) switches, theses multiple references can internally be routed to the receiver input without any mechanical wear. As a result, laborious external references can be omitted and the repetition rate of the calibration procedure increased, which results in a higher radiometric accuracy and allows a more compact and cost-effective design of modern radiometer systems. This work presents the first radiometric calibration front-end that allows to internally switch between active electronic cold and active electronic hot loads, as well as a passive ambient load. All components are integrated on a single MMIC, and a patent was granted for this innovation. To predict the achievable noise temperatures of active cold loads (ACLs), different simulation approaches were previously published. This work evaluates and adapts these existing approaches to design and manufacture several W-band loads. But the required design-flow was found to be very time-consuming because multiple iterations are necessary to successively design and optimize the input- and output matching networks, and to finally achieve the desired low noise temperature. Therefore, a novel simulation approach is introduced that makes efficiently use of modern optimization algorithms and the very accurate model library of the mHEMT technology and the passive structures. With this novel simulation method, the first active hot loads (AHLs) were designed as well as state-of-the-art ACLs up to 140 GHz. However, the characterization of low-noise one-port devices is particularly challenging, especially at such high frequencies. Hence, a substantial part of this work is to investigate the reliability of different noise measurement setups and the repeatability of noise temperature results. Dedicated setups in W- and D-band are used to characterize all manufactured active loads and some selected results are cross-checked by measuring the same circuits with independently designed measurement systems of other research facilities. The discrepant results are discussed, concluding that high variations in measured one-port noise temperature do not allow to rely on one single measurement setup. At the same time, this thorough investigation and comparison permits to establish an accuracy range within which the results of the manufactured active electronic loads are reliable, whereas other previously published ACLs are typically only measured with one measurement setup.Item Open Access Auslegung und Inbetriebnahme eines leistungsstarken und kompakten SiC Wechselrichters(2021) Volz, FredericDie vorliegende Arbeit befasst sich mit der Konzipierung, dem Aufbau und der Inbetriebnahme eines dreiphasigen Wechselrichters mit Leistungs-MOSFETs aus Siliziumkarbid, welcher die Lebensdaueruntersuchung unter realen Betriebsbedingungen ermöglichen soll. Der SiC Wechselrichter wird hierfür mit einem speziell für Lebensdaueruntersuchungen abgestimmten Kühlsystem ausgestattet. Im Rahmen der vorliegenden Masterarbeit findet die Integration des SiC Wechselrichters in einen Prüfstand mit einem ein- und ausgangsseitig gekoppelten Wechselrichter statt, welcher künftig als aktiver Power Cycling Prüfstand betrieben wird. Hierdurch wird eine gezielte Bauteilalterung unter realen Betriebsbedingungen ermöglicht.Item Open Access Sharp MIR plasmonic modes in gratings made of heavily doped pulsed laser-melted Ge1-xSnx(2023) Berkmann, Fritz; Steuer, Oliver; Ganss, Fabian; Prucnal, Slawomir; Schwarz, Daniel; Fischer, Inga Anita; Schulze, JörgItem Open Access Precise voltage measurement for power electronics with high switching frequencies(2018) Nitzsche, Maximilian; Zehelein, Matthias; Tröster, Nathan; Roth-Stielow, JörgIn this paper different approaches in precise measurement of gate voltages as well as drain-source voltages of modern SiC and GaN transistors are compared. An approach to calculate the necessary bandwidth of a voltage probe to reproduce the voltage slope is presented. Furthermore, state-of-the-art voltage probes are compared in means of bandwidth, common mode reduction and response on EMI.Item Open Access Molekularstrahlepitaxie und Charakterisierung unverspannter Silizium-Germanium-Zinn-Legierungen auf virtuellem Germanium-Substrat(2022) Schwarz, Daniel; Schulze, Jörg (Prof. Dr. habil.)Item Open Access Quantitative analysis of the sensitivity of UHF sensor positions on a 420 kV power transformer based on electromagnetic simulation(2019) Beura, Chandra Prakash; Beltle, Michael; Tenbohlen, Stefan; Siegel, MartinWith an increasing interest in ultra-high frequency (UHF) partial discharge (PD) measurements for the continuous monitoring of power transformers, it is necessary to know where to place the UHF sensors on the tank wall. Placing a sensor in an area with many obstructions may lead to a decrease in sensitivity to the UHF signals. In this contribution, a previously validated simulation model of a three-phase 300 MVA, 420 kV power transformer is used to perform a sensitivity analysis to determine the most sensitive sensor positions on the tank wall when PD activity occurs inside the windings. A matrix of UHF sensors located on the transformer tank is used to perform the sensitivity analysis. Some of the windings are designed as layer windings, thus preventing the UHF signals from traveling through them and creating a realistic situation with very indirect propagation from source to sensor. Based on these findings, sensor configurations optimized for UHF signal sensitivity, which is also required for PD source localization, are recommended for localization purposes. Additionally, the propagation and attenuation of the UHF signals inside the windings and the tank are discussed in both oil and air.Item Open Access Analytic free-energy expression for the 2D-Ising model and perspectives for battery modeling(2023) Markthaler, Daniel; Birke, Kai PeterAlthough originally developed to describe the magnetic behavior of matter, the Ising model represents one of the most widely used physical models, with applications in almost all scientific areas. Even after 100 years, the model still poses challenges and is the subject of active research. In this work, we address the question of whether it is possible to describe the free energy A of a finite-size 2D-Ising model of arbitrary size, based on a couple of analytically solvable 1D-Ising chains. The presented novel approach is based on rigorous statistical-thermodynamic principles and involves modeling the free energy contribution of an added inter-chain bond DAbond(b, N) as function of inverse temperature b and lattice size N. The identified simple analytic expression for DAbond is fitted to exact results of a series of finite-size quadratic N N-systems and enables straightforward and instantaneous calculation of thermodynamic quantities of interest, such as free energy and heat capacity for systems of an arbitrary size. This approach is not only interesting from a fundamental perspective with respect to the possible transfer to a 3D-Ising model, but also from an application-driven viewpoint in the context of (Li-ion) batteries where it could be applied to describe intercalation mechanisms.