06 Fakultät Luft- und Raumfahrttechnik und Geodäsie
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/7
Browse
34 results
Search Results
Item Open Access Rheology, dispersion, and cure kinetics of epoxy filled with amine‐ and non‐functionalized reduced graphene oxide for composite manufacturing(2021) Ackermann, Annika C.; Carosella, Stefan; Rettenmayr, Markus; Fox, Bronwyn L.; Middendorf, PeterThis study evaluates the effect of plasma surface functionalization of reduced graphene oxide particles on the processing characteristics and homogeneity of dispersion of a bisphenol A‐(epichlorhydrin) epoxy matrix and amine‐based hardener with varying weight fractions from 0.00 to 1.50 wt%. It was observed that amine‐functionalized reduced graphene oxide leads to a more drastic viscosity increase of up to 18‐fold of the uncured suspensions and that its presence influences the conversion rates of the curing reaction. Optical microscopy of thin sections and transmission electron microscopy analysis showed that a more homogeneous dispersion of the particles could be achieved especially at higher weight fractions by using an appropriate surface functionalization. This knowledge can be used to define suitable processing conditions for epoxies with amine‐based hardeners depending on the loading and functionalization of graphene‐related particles.Item Open Access IEA Wind Task 32: Wind Lidar : identifying and mitigating barriers to the adoption of wind lidar(2018) Clifton, Andrew; Clive, Peter; Gottschall, Julia; Schlipf, David; Simley, Eric; Simmons, Luke; Stein, Detlef; Trabucchi, Davide; Vasiljevic, Nikola; Würth, InesIEA Wind Task 32 exists to identify and mitigate barriers to the adoption of lidar for wind energy applications. It leverages ongoing international research and development activities in academia and industry to investigate site assessment, power performance testing, controls and loads, and complex flows. Since its initiation in 2011, Task 32 has been responsible for several recommended practices and expert reports that have contributed to the adoption of ground-based, nacelle-based, and floating lidar by the wind industry. Future challenges include the development of lidar uncertainty models, best practices for data management, and developing community-based tools for data analysis, planning of lidar measurements and lidar configuration. This paper describes the barriers that Task 32 identified to the deployment of wind lidar in each of these application areas, and the steps that have been taken to confirm or mitigate the barriers. Task 32 will continue to be a meeting point for the international wind lidar community until at least 2020 and welcomes old and new participants.Item Open Access Technology selection for holistic analysis of hybrid-electric commuter aircraft(2022) Zumegen, Clemens; Strathoff, Philipp; Stumpf, Eike; Wensveen, Jasper van; Rischmüller, Carsten; Hornung, Mirko; Geiß, Ingmar; Strohmayer, AndreasElectric powertrains have different characteristics than conventional powertrains with combustion engines and require unconventional aircraft designs to evolve their full potential. Therefore, this paper describes a method to identify potential aircraft designs with electrified powertrains. Promising technology options in the fields of powertrain architecture, aerodynamic interactions, onboard systems and operating strategies were collected by the project partners of the LuFo project GNOSIS. The effect of the technology options on a commuter aircraft was evaluated in terms of global emissions ( CO2), local emissions ( NOXand noise) and operating costs. The evaluation considers an entry into service in 2025 and 2050 and is based on the reference aircraft Beechcraft 1900D. Literature review and simplified calculations enabled the evaluation of the aerodynamic interactions, systems and operating strategies. A preliminary aircraft design tool assessed the different powertrain architectures by introducing the two parameters ’power hybridization’ and ’power split’. Afterwards, compatible technology options were compiled into technology baskets and ranked using the shortest euclidean distance to the ideal solution and the farthest euclidean distance to the worst solution (Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) method). An analysis of the CS 23 regulations leads to a high-wing design and excluded the partial turbo-electric powertrain architecture with the gas turbine in the aircraft tail. For 2025, a partial turbo-electric powertrain with two additional electric driven wingtip propellers was selected. A serial hybrid powertrain, which uses a gas turbine or fuel cell in combination with a battery, powers distributed electric propulsors at the wing leading edge in 2050. In both scenarios, the aircraft design includes an electric environmental control system, an electric driven landing gear and electro-hydraulic actuators for the primary flight control and landing gear.Item Open Access Digital function modeling in graph-based design languages(2022) Elwert, Michael; Ramsaier, Manuel; Eisenbart, Boris; Stetter, Ralf; Till, Markus; Rudolph, StephanThe main focus of this paper is the integration of an integrated function modeling (IFM) framework in an engineering framework based on graph-based design languages (GBDLs). Over the last decade, GBDLs have received increasing attention as they offer a promising approach for addressing several important challenges in engineering, such as the frequent and time-consuming transfer of data between different computer aided engineering (CAE) tools. This absorbs significant amounts of manual labor in engineering design projects. GBDLs create digital system models at a meta level, encompassing all relevant information concerning a certain product design and feeding this into the relevant simulation tools needed for evaluating the impact of possible design variations on the performance of the resulting products/parts. It is possible to automate this process using digital compilers. Because of this, it is also possible to realize systematic design variations for a very large number of parameters and topological variants. Therefore, these kinds of graph-based languages are a powerful means for creating a large number of viable design alternatives and for permitting fast evaluation processes against the given specifications. While, thus far, such analyses tend to be based on a more or less fully defined system, this paper proposes an expansion of the applicability of GBDLs into the domain of product functions to cohesively link conceptual with embodiment design stages. This will also help with early systematic, automated generation and the validation of design alternatives through relevant simulation tools during embodiment design. Further, it will permit the automated exploration of function paths and enable extended analysis possibilities, such as the detection of functional bottlenecks, while enhancing the traceability of the design over the development process. For these extended analysis possibilities, a function analysis tool was developed that adopts core ideas of the failure mode and effects analysis (FMEA). In this, the functional distinction between function carriers and function-related processes allows the goal-directed assessment of component reliabilities and the detectability and importance of processes in a technical system. In the paper, the graph-based modeling of functions and the function analysis tools are demonstrated on the example of a multicopter.Item Open Access High-performance properties of an aerospace epoxy resin loaded with carbon nanofibers and glycidyl polyhedral oligomeric silsesquioxane(2022) Guadagno, Liberata; Pantelakis, Spiros; Strohmayer, Andreas; Raimondo, MarialuigiaThis paper proposes a new multifunctional flame retardant carbon nanofiber/glycidyl polyhedral oligomeric silsesquioxane (GPOSS) epoxy formulation specially designed for lightweight composite materials capable of fulfilling the ever-changing demands of the future aerospace industry. The multifunctional resin was designed to satisfy structural and functional requirements. In particular, this paper explores the advantages deriving from the combined use of GPOSS and CNFs (short carbon nanofibers) to obtain multifunctional resins. The multifunctional material was prepared by incorporating in the epoxy matrix heat-treated carbon nanofibers (CNFs) at the percentage of 0.5 wt% and GPOSS compound at 5 wt% in order to increase the mechanical performance, electrical conductivity, thermal stability and flame resistance property of the resulting nanocomposite. Dynamic mechanical analysis (DMA) shows that the values of the Storage Modulus (S.M.) of the resin alone and the resin containing solubilized GPOSS nanocages are almost similar in a wide range of temperatures (from 30 °C to 165 °C). The presence of CNFs, in the percentage of 0.5 wt%, determines an enhancement in the S.M. of 700 MPa from −30 °C to 180 °C with respect to the resin matrix and the resin/GPOSS systems. Hence, a value higher than 2700 MPa is detected from 30 °C to 110 °C. Furthermore, the electrical conductivity of the sample containing both GPOSS and CNFs reaches the value of 1.35 × 10−1 S/m, which is a very satisfying value to contrast the electrical insulating property of the epoxy systems. For the first time, TUNA tests have been performed on the formulation where the advantages of GPOSS and CNFs are combined. TUNA investigation highlights an electrically conductive network well distributed in the sample. The ignition time of the multifunctional nanocomposite is higher than that of the sample containing GPOSS alone of about 35%.Item Open Access Response of the International Energy Agency (IEA) Wind 15 MW WindCrete and Activefloat floating wind turbines to wind and second-order waves(2021) Mahfouz, Mohammad Youssef; Molins, Climent; Trubat, Pau; Hernández, Sergio; Vigara, Fernando; Pegalajar-Jurado, Antonio; Bredmose, Henrik; Salari, MohammadItem Open Access Graph transformation in engineering design : an overview of the last decade(2023) Voss, Christopher; Petzold, Frank; Rudolph, StephanItem Open Access FAST.Farm load validation for single wake situations at alpha ventus(2021) Kretschmer, Matthias; Jonkman, Jason; Pettas, Vasilis; Cheng, Po WenThe main objective of the presented work is the validation of the simulation tool FAST.Farm for the calculation of power and structural loads in single wake situations; the basis for the validation is the measurement database of the operating offshore wind farm alpha ventus. The approach is described in detail and covers the calibration of the aeroelastic turbine model, transfer of environmental conditions to simulations, and comparison between simulations and adequately filtered measurements. It is shown that FAST.Farm accurately predicts power and structural load distributions over wind direction with discrepancies of less than 10 % for most of the cases compared to the measurements. Additionally, the frequency response of the structure is investigated, and it is calculated by FAST.Farm in good agreement with the measurements. In general, the calculation of fatigue loads is improved with a wake-added turbulence model added to FAST.Farm in the course of this study.Item Open Access Thermomechanical analysis of thermoplastic mono-material sandwich structures with honeycomb core(2024) Latsuzbaya, Temuri; Middendorf, Peter; Voelkle, Dietmar; Weber, ChristophThe application of fiber-reinforced thermoplastic mono-material sandwich panels has many advantages, such as recyclability, reduction in processing cycle times, integration of additional elements by means of welding, and a great potential for in-line production. The most efficient way to produce a curved thermoplastic sandwich panel is thermoforming, which has several challenges. One of them is to achieve a higher thermal gradient in the panel. On the one hand, the temperature at the skin-core interface must exceed the softening point of the polymer to reach a sufficient bonding degree. On the other hand, the core should not be overheated and overloaded to avoid its collapse. Furthermore, several fiber distortions, such as wrinkles or buckles, can be developed during thermoforming. All these flaws have a negative impact on the mechanical performance of the sandwich structure. The objective of this study is the development of a simulation tool for the thermoforming process, which can replace the time-consuming trial-and-error-based method. Therefore, a coupled thermomechanical model was developed for a novel thermoplastic sandwich structure, which is able to predict the temperature distribution and its influence on the mechanical properties of the panel. Experimental trials were conducted to validate the thermomechanical forming model, which demonstrated a good agreement with numerical results.Item Open Access Influence of electric wing tip propulsion on the sizing of the vertical stabilizer and rudder in preliminary aircraft design(2023) Albrecht, Alexander; Bender, Andreas; Strathoff, Philipp; Zumegen, Clemens; Stumpf, Eike; Strohmayer, AndreasDuring preliminary aircraft design, the vertical tail sizing is conventionally conducted by the use of volume coefficients. These represent a statistical approach using existing configurations’ correlating parameters, such as wing span and lever arm, to size the empennage. For a more detailed analysis with regard to control performance, the vertical tail size strongly depends on the critical loss of thrust assessment. This consideration increases in complexity for the design of the aircraft using wing tip propulsion systems. Within this study, a volume coefficient-based vertical tail plane sizing is compared to handbook methods and the possibility to reduce the necessary vertical stabilizer size is assessed with regard to the position of the engine integration and their interconnection. Two configurations, with different engine positions, of a hybrid-electric 19-seater aircraft, derived from the specifications of a Beechcraft 1900D, are compared. For both configurations two wiring options are assessed with regard to their impact on aircraft level for a partial loss of thrust. The preliminary aircraft design tool MICADO is used to size the four aircraft and propulsion system configurations using fin volume coefficients. These results are subsequently amended by handbook methods to resize the vertical stabilizer and update the configurations. The results in terms of, e.g., operating empty mass and mission fuel consumption, are compared to the original configurations without the optimized vertical stabilizer. The findings support the initial idea that the connection of the electric engines on the wing tips to their respective power source has a significant effect on the resulting torque around the yaw axis and the behaviour of the aircraft in case of a power train failure, as well as on the empty mass and trip fuel. For only one out of the four different aircraft designs and wiring configurations investigated it was possible to decrease the fin size, resulting in a 53.7% smaller vertical tail and a reduction in trip fuel of 4.9%, compared to the MICADO design results for the original fin volume coefficient.