Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
2 results
Search Results
Item Open Access Anion exchange membranes for fuel cells and flow batteries : transport and stability of model systems(2015) Marino, Michael G.; Maier, Joachim (Prof. Dr.)Polymeric anion exchange materials in membrane form can be key components in emerging energy storage and conversions systems such as the alkaline fuel cell and the RedOx flow battery. For these applications the membrane properties need to include good ionic conductivity and sufficient chemical stability, two aspects, that are not sufficiently understood in terms of materials science. Materials fulfilling both criteria are currently not available. The transport of ions and water in a model anion exchange membrane (AEM) as well as the alkaline stability of their quaternary ammonium functional groups is therefore investigated in this thesis from a basic point of view but with the aim to bring these technologies one step closer to large scale application, as they have several advantages compared to existing energy storage and conversion systems. The hydroxide exchanging alkaline fuel cell (AFC), for example, is in principle more cost-effective than the more common acidic proton exchange fuel cell (PEMFC). Unfortunately AFCs suffer from base induced decomposition of the membrane. Especially the quaternary ammonium (QA) functional groups are easily attacked by the nucleophilic hydroxide. QAs with higher alkaline stability are required but there is considerable disagreement regarding which QAs are suitable, with widely varying and partially contradicting results reported in the literature. In this thesis, the decay of QA salts was investigated under controlled accelerated aging conditions (up to 10 M NaOH and 160 °C). This allowed a stability comparison based solely on the molecular structure of the QAs. A number of different approaches to stabilize the QAs which potentially inhibit degradation reactions such as β-elimination, substitution and rearrangements were compared. These include β-proton removal, charge delocalization, spacer-chains, electron-inducing groups and conformational confinement. Heterocylic 6-membered QAs based on the piperidine structure proved to be by far the most stable cations at the chosen conditions. This was not readily apparent from their structure since they contain β-protons in anti-periplanar positions, which generally cause rapid decomposition in other types of QAs. The geometry of the cyclic structure probably exerts strain on the reaction transition states, kinetically inhibiting the degradation reactions. Other stabilization approaches resulted in markedly less stable compounds. Noticeably the benzylic group, which is the current standard covalent tether between QA and polymer, degrades very fast compared to almost all aliphatic QAs. The results of this stability study suggest that hydroxide exchange membranes for alkaline fuel cells, which are significantly more stable than current materials are achievable. Besides stability, the transport of anions and water in AEMs was investigated in this Hydroxide exchange membranes (HEM) have been reported to exhibit surprisingly low ionic conductivities compared to their proton exchange membrane (PEM) counterparts. This is partially because hydroxide charge carriers are rapidly converted to carbonates when a HEM comes into contact with ambient air. Careful exclusion of CO2 was required to investigate pure hydroxide form membranes. For this purpose a custom glove box was designed and built that allowed preparation and measurements of HEM samples in a humidified CO 2 -free atmosphere. It was found that the conductivity reduction of a carbonate contaminated HEM is not only due to the reduced ionic mobility of carbonate charge carriers compared to hydroxide, but also because of reduced water absorption of the corresponding membrane which decreases conductivity even further. Pure HEMs can in fact achieve conductivities within a factor of two of PEMs at equal ion exchange capacity at sufficient hydration, according to the differences in the ionic mobility of hydroxide and hydronium. At lower water contents though, the hydroxide mobility decreases faster than that of hydronium in comparable PEMs due to reduced dissociation and percolation as well as a break-down of structural diffusion Apart from the HEM, membranes in other ionic forms were investigated. Generally, all investigated AEM properties were found to change if the type of anion was exchanged. This comprises the degree of dissociation, conductivity, membrane morphology and sometimes even water diffusion. Remarkably, at low water contents, the ionic conductivity of the HEM sank below that of the halides, despite the much higher hydroxide mobility in aqueous solution. A gradual break-down of the hydroxide structural diffusion is probably responsible. Another noticeable observation was that the degree of dissociation for at least the bromide and chloride form membranes remains almost constant over a considerable water content range, suggesting the formation of associates consisting of several ions, which probably also exists in other ionic forms.Item Open Access In situ characterization of phase evolution in LiFePO4(2015) Ohmer, Nils; Maier, Joachim (Prof. Dr.)Among the candidates for electrodes in future Li-based batteries, LiFePO4 (LFP) is one of the most important and most frequently studied materials, undergoing a phase transformation upon delithiation to FePO4 (FP). In spite of the great scientific and practical interest in this material, there is still an extensive debate on the mechanism of this phase transformation and the underlying factors of influence. Within the framework of this thesis, first studies are carried out ex situ on multi-particle, full electrode LFP materials, being electrochemically cycled and analyzed at various states of charge by a combination of highly spatially resolved methods (high-resolution transmission electron microscopy and electron energy loss spectroscopy (HRTEM, EELS)) and integral measurement techniques (analyzing the X-ray diffraction and X-ray absorption near edge structure (XRD, XANES)). This combination of characterization techniques allows one to distinguish between the cycling behaviour of differently sized crystallites within the same electrode. It is found that for electrodes with hydrothermally grown LFP as active material, a particle size dependent cycling behaviour exists, with nanosized particles apparently not participating in the charging process at all. A turbostratic stacking of layers in these nanosized particles is found and identified to be responsible for sluggish lithium insertion and extraction. These higher dimensional defects prevent the small particles from participating in the charging process, most likely by disturbing the lithium diffusion along the 1-dimensional channels, as well as impair the transport along the other directions in the LFP host structure and thus blocking the lithium transport, resulting in a comparibly lower practical capacity during electrochemical cycling. To study the lithium exchange mechanism upon charging a LFP thin film cathode, an all-solid-state thin film battery cell with a lateral design concept is developed and realized by pulsed laser deposition (PLD) and thermal evaporation techniques. Using PLD and shadow masks LFP cathode, Li2O-V2O5-SiO2 (LVSO) electrolyte and LiAl anode thin films are deposited sequentially in a way that the Li transport pathway in the resulting battery is along the X-ray transparent commercial Si3N4 membrane substrate. This enables the usability of synchrotron-based energy resolved scanning transmission X-ray microscopy (STXM) with its high chemical and spatial resolution to perform in situ absorption measurements at the Fe L3 edge. Upon delithiation, a shift in the main absorption feature from 708 to 710 eV is used to fingerprint the change in the local state of charge, identifying areas containing Fe2+ (lithiated) and Fe3+ (delithiated), respectively. The initial lithiation process of a LFP thin film cathode material has been followed by in situ STXM, with a lateral resolution of 30 nm, during electrochemical charging of the thin film battery. The observed initial lithiation process does not follow the classical particle by particle mechanism, typical for multi-particle LFP cathodes, but instead a rather simultaneous, although inhomogeneous, lithiation is observed. The reason for this change in mechanism, compared to multi-particle powder electrodes, is found in mechanical interactions within the thin film upon lithiation, i.e. in the corresponding volume expansion and formation of high energy surfaces, changing the shape of the single-particle chemical potential to a monotone form upon lithiation. This has far-reaching consequences: not only the many-particle mechanism is changed to a concurrent lithiation, but also the single-particle mechanism is changed from a two-phase to a single-phase mechanism upon lithiation. Furthermore, a vanishing hysteresis loop and the disappearing of the memory effect is predicted. These findings are rather general and applicable to all kind of thin films of phase separating intercalation materials, undergoing a volume change upon lithium exchange. To fill the gap in literature on in situ observations of the (L)FP phase evolution on a single-particle level with appreciable space and time resolution, a micrometer-sized all-solid-state thin film battery is built with a defect-chemically well characterized LFP single crystal as cathode material with dimensions of 16x1x0.2 micrometer. Using STXM, the phase evolution along the fast (010) orientation is followed during in situ electrochemical (de)lithiation on a micro-meter scale with a lateral resolution of 30 nm and with minutes of time resolution. Furthermore, the STXM measurements performed on this sample are one of the few experiments ever taken on LFP materials with a well defined defect chemistry, even though fundamentally necessary for an overall understanding of the materials behaviour. This combination discloses not only the mechanism of LFP transformation on a single-particle level, but also the significance of elastic effects on the (de)lithiation process. Using a defect chemical analysis, the position of phase formation is found to be determined by the defect chemical situation, while the growth pattern of both LFP and FP is found to be dominated by elastic effects.