Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
Search Results
Item Open Access Modeling and simulation of closed low-pressure adsorbers for thermal energy storage(2019) Schäfer, Micha; Thess, André (Prof. Dr. rer. nat.)Closed low-pressure adsorption systems can be applied for thermal energy storage. Their performance is determined by the mass and heat transport processes in the adsorber. Therefore, thorough knowledge of these transport processes is required for further storage development. The present thesis contributes to this by providing detailed models of closed low-pressure adsorbers and by conducting simulations over a broad range of parameters and configurations. The focus is on adsorbers of larger scale (length L = 0.1 . . . 1 m) and on the discharging process. As the adsorption pair, binderless zeolite 13X with water is examined. The models are developed in a stepwise manner from pore to storage scale. The Finite-Difference-Method is implemented to numerically solve the models. Simulations are conducted for defined reference cases as well as over a broad range of geometric and process parameters. The reference cases are analyzed in detail to gain a better understanding of the transport processes. Furthermore, the results are analyzed with respect to two particular modeling aspects: equilibrium assumptions and rarefaction effects (e. g. slip effect). With respect to the application, the discharging performance is analyzed in terms of thermal power and a defined discharging degree. Both the adsorber and the adsorbent configurations are varied. In addition, the effect of the discharging conditions is evaluated. Finally, one exemplary charging process is examined. The detailed analysis of the reference cases reveals that the mass and heat transport and the adsorption processes are strongly coupled and can only be understood in their interaction. For onedimensional adsorber configurations, that is the mass and heat transport are in the same direction, the discharging process is generally limited by the heat transport. This leads to insufficient thermal power and unsuitable discharging durations of up to one year. In contrast, for two-dimensional adsorber configurations, that is the mass and heat transport are in perpendicular directions, the discharging process can be limited either by the mass or heat transport or by the adsorption. The limitation depends on the configuration of the adsorber and adsorbent. Moreover, the twodimensional adsorber configurations can provide sufficient thermal power. With respect to the modeling, it is found that the assumption of a uniform pressure distribution is applicable for one-dimensional adsorber configurations. In contrast, for two-dimensional configurations, no equilibrium assumptions can be applied in general. However, for powder adsorbent it is always valid to assume local adsorption equilibrium. Regarding the rarefaction effects in twodimensional adsorber configurations with honeycombs and granules, the slip effect is relevant for small channel and particle diameters (d = 1 mm). For adsorbers with powder adsorbent, the reduction of the effective heat conductivity due to the rarefaction effect becomes relevant. With respect to the application, the variation of the adsorber configuration shows that the volumetric thermal power generally decreases with increasing adsorber length. Furthermore, the power decreases with increasing width between the parallel heat exchanger plates in the adsorber. Regarding the adsorbent configuration in two-dimensional adsorber configurations, it is found that the volumetric thermal power can be optimized by variation of the channel or particle diameter. Interestingly, the optima for peak and mean power do not coincide. In addition, the discharging degree is found to strongly depend on the discharging conditions in terms of discharging temperature and volume flow of the heat transfer fluid extracting the heat from the adsorber. In general, the discharging degree decreases with increasing discharging temperature. Similarly, the discharging degree decreases with increasing volume flow of the heat transfer fluid. Finally, the analysis of an exemplary charging process revealed that the pressure in the adsorber can increase significantly (> 50%) due to the desorption.Item Open Access Chirale lyotrop-lamellare Flüssigkristalle : Phasenverhalten neuer chiraler Amphiphile und Nachweis des elektroklinen Effektes(2019) Harjung, Marc D.; Gießelmann, Frank (Prof. Dr.)Ziel dieser Arbeit ist es, neue Erkenntnisse zur Bildung lyotroper SmC*-Phasen zu gewinnen und einen elektroklinen Effekt in chiral lamellaren Phasen nachzuweisen.Item Open Access Novel X-ray lenses for direct and coherent imaging(2019) Sanli, Umut Tunca; Schütz, Gisela (Prof. Dr.)Item Open Access Chirality effects in thermotropic and lyotropic nematic liquid crystals under confined geometries(2019) Dietrich, Clarissa; Giesselmann, Frank (Prof. Dr.)Chirality is a phenomenon in nature that appears across all disciplines of natural science, from biology to mathematics. The spontaneous formation of chiral structures in a system of achiral components is known as spontaneous mirror symmetry breaking and is by itself of fundamental interest leading also towards the question of the origin of homochirality in nature in general. In this work, we show that by means of the topology imposed by the confining geometry and by interfacial boundary conditions - in combination with the physical properties of a liquid crystal - spontaneous mirror symmetry broken structures can be obtained. They are analyzed, inter alia, with respect to the types of geometrical confinements used, e.g. how the confinement amplifies, induces, and influences the detection of chirality effects in order to facilitate the measurement of tiny amounts of chiral additives qualitatively and quantitatively.Item Open Access Herstellung von Acrylnitril aus biobasierter Milchsäure und Propionsäure(2019) Mack, Daniel; Klemm, Elias (Prof. Dr.-Ing.)Item Open Access Biochemical characterization and identification of novel substrates of protein lysine methyltransferases(2019) Schuhmacher, Maren Kirstin; Jeltsch, Albert (Prof. Dr.)The methylation of lysine side chains is a prevalent post-translational modification (PTM) of proteins, which is introduced by protein lysine methyltransferases (PKMTs). Histone methylation can have different effects on chromatin structure, lysine methylation of non-histone proteins can regulate protein/protein interactions and protein stability. For most PKMTs currently not all methylation sites are known which limits our understanding of the regulatory role of these enzymes in cells. Therefore, it is an important research aim to gain more information about the substrate spectrum of PKMTs. The identification of the substrate specificity of a PKMT is a very important step on the way to identify new PKMT methylation sites. The focus of this study was the analysis of the substrate specificity of different PKMTs by SPOT peptide arrays and based on this on the identification and validation of possible new methylation substrates. The analysis of the substrate specificity of human SUV39H2 revealed significant differences to its human homolog SUV39H1, although both enzymes methylate the same histone substrate (H3K9). SUV39H2 is more stringent than the SUV39H1, which could be demonstrated by the lack of methylation of SUV39H1 non-histone targets by SUV39H2 and by the fact that it was not possible in this study to identify non-histone substrates for SUV39H2. Kinetic studies showed that SUV39H2 prefers the unmethylated H3K9 as substrate. Moreover, it was shown that the N324K mutation of SUV39H2 which leads to a genetic disease in Labrador retrievers causes a change in folding finally leading to the inactivation of the enzyme. It had been reported by another group that the histone variant H2AX is methylated by SUV39H2. However, the sequence of H2AX K134 does not fit to the substrate specificity profile of SUV39H2 determined in the present work. Follow-up in vitro peptide and protein methylation studies indeed showed that H2AX K134 is not methylated by SUV39H2. This indicates that H2AX methylation by SUV39H2 is most probably a wrong assignment of a substrate to a PKMT. Based on already available specificity data for the SUV39H1 PKMT, the SET8 protein was validated as novel substrate in cellular studies. SET8 is a PKMT itself and it could be shown in this thesis that methylation of SET8 at residue K210 by SUV39H1 stimulated the SET8 activity. In humans, there exist different PKMTs, which methylate H3K36. For example, NSD1, NSD2 and SETD2 which were investigated in this thesis. In literature, it was shown that the oncohistone mutation K36M inactivates NSD2 and SETD2. Steady-state methylation kinetics using a peptide substrate and a K36M peptide as inhibitor revealed that NSD1 is inhibited by this histone oncomutation as well. The steady-state inhibition parameters for all enzymes showed a better binding of the PKMTs to the inhibitor peptide than to the substrate, suggesting some mechanistic similarities in target peptide interaction. The SETD2 is a methyltransferase, which is able to introduce trimethylation of H3K36. During this thesis two substrate specificity motifs of SETD2 were determined using peptide array methylation experiments. Additionally, based on the substrate specificity investigations a super-substrate at peptide and protein level was determined. Furthermore, one novel substrate (FBN1) for SETD2 was discovered and validated. The Legionella pneumophila RomA PKMT was shown previously by our collaborators to methylate H3 at K14. Based on the specificity profile of RomA determined in this study it could be shown that this enzyme methylates seven additional human non-histone proteins. Collaborators tested the methylation of one of the non-histone targets (AROS) and could demonstrate its methylation during the infection of human cells with L. pneumophila. The role of these methylation events in the infection process must be studied in future experiments.Item Open Access Catalytic enantioselective total synthesis of picrotoxane alkaloids and guaiane sesquiterpene englerins A and B(2019) Guo, Lei; Plietker, Bernd (Prof.Dr.)Alkaloids from the picrotoxane family are biologically potent natural products that show hypertensive, antipyretic, analgesic and anti-influenza A virus activities. Herein a concise catalytic, enantioselective total synthesis of (-)-dendrobine, (-)-mubironine B and (-)-dendroxine is described with an overall yield of 6.7%, 7.8% and 7.4%, respectively. This represents a significantly improved yield as compared to synthetic approaches reported in the past, and it is the first report on the total synthesis of (-)-dendroxine. Importantly, the asymmetric Yb-catalyzed Diels-Alder reaction between Danishefsky’s diene and an oxazolidinone moiety allowed for an enantioselective synthesis of the natural products in the enantioselective way, while the Fe-catalyzed aerobic oxidation, Cu- or Au-catalyzed cycloisomerization and hydroazidation underlined the strength of modern synthetic sequences in total synthesis. Englerin A is a guaiane sesquiterpene natural product that shows antitumor activity when binding to the TRPC4/5 target (a new target for antitumor compounds) in vitro. In this part a bio-inspired, catalytic enantioselective strategy towards the total synthesis of (-)-englerins A and B in 12 or 13 steps with 6.7% or 4.8% yield, respectively, is described. The success was initialized by a biomimetic catalytic enantioselective decarboxylative aldol reaction for chirality introduction. A [4+3] cycloaddition with neighboring group participation was used for the construction of the central core structure, which was inspired by the biogenesis of tropinone. A late stage one-pot Heck coupling-regioselective hydrosilylation-Fleming oxidation cascade sequence afforded the cyclopentane core while a kinetic CBS reduction enriched enantiopurity and eventually delivered the natural products.Item Open Access Wetting, de-icing and anti-icing behavior of microstructured and plasma-coated polyurethane films(2019) Grimmer, Philipp E. S.; Hirth, Thomas (Prof. Dr. rer. nat.)Ice build-up on surfaces, for example on wings of airplanes or on rotor blades of wind turbines, impairs the functionality of transportation vehicles or technical systems and reduces their safety. Therefore, functional anti-ice surfaces are being researched and developed, which shall enable an easy removal or reduce the amount of ice on the surfaces at risk. The starting hypothesis for this work is that superhydrophobic polyurethane (PU) films with microstructure base diameters of 35 µm or more reduce the wetting by water, show a low ice adhesion for easy removal of ice and reduce or delay icing. Superhydrophobic PU films for passive anti- and de-icing were created by hot embossing and plasma enhanced chemical vapor deposition (PECVD). The hot embossing process as well as the plasma coating and etching processes were analyzed for the dependence of the surface characteristics on different process parameters. The functionalized PU films were characterized for their surface topography, surface chemistry, stability against erosion, wettability, ice adhesion and icing behavior. For comparison, the ice adhesion and icing behavior were examined on relevant technical materials (aluminum, titanium, copper, glass, epoxy resin of carbon fiber reinforced polymer and other fluoropolymers) and on some commercial anti-ice coatings. The PU films were chemically analyzed by IR spectroscopy. As the first process step for functionalization, microstructures of cylindrical, elliptical or linear shape were imprinted in PU films by a hot embossing technique with different ns-pulsed laser-drilled stamps and characterized by several microscopy methods. The microstructures had heights of 15 µm to 140 µm, diameters or widths of 35 µm to 300 µm and distances (pitch values) of 50 µm to 500 µm. The embossing process was analyzed and optimized in terms of the process parameters temperature, pressure, time, PU film release temperature and reproducibility of the microstructures. In a second functionalization step (PECVD) the microstructured surfaces were coated with thin, hydrophobic plasma polymers using different fluorocarbon precursors (CHF3, C3F6 and C4F8) or hexamethyldisiloxane (HMDSO). Different process parameters for plasma coating and etching (Ar or O2 plasmas) were used in order to create various nanoscale roughness values. Electron spectroscopy for chemical analysis (ESCA), spectroscopic ellipsometry and atomic force microscopy (AFM) were used for analysis of the chemical composition, the thickness and the nanoroughness of the plasma polymers. The functionalizations, especially the plasma coatings, were completely worn off by a UV/water weathering test (1000 h, X1a CAM 180 Test, SAE J-2527), but showed sufficient stability against sand erosion (DIN 52348), in a long-term outdoor test for 13.5 months and against fivefold repeated pull-off of ice. The silicone-like plasma coatings were more stable than the fluorocarbon plasma coatings. The wetting behavior of water was determined by static, advancing and receding contact angle measurements. Static contact angle measurements with diiodomethane (DIM) were made for determination of the surface free energies of the relevant surfaces. Advancing contact angles of over 150° and very low contact angle hysteresis values below 10° were reached on some of the cylindrically and elliptically structured PU samples with microstructure base diameters in the range of 35 µm to 50 µm. The measured water advancing contact angles did not reach the theoretical values of the Cassie-Baxter state. Starting from a mixed wetting state near Cassie-Baxter in case of the superhydrophobic PU surfaces, they approached the Wenzel state with an increasing pitch/diameter (P/d) factor. Fluorescence laser scanning microscopy images were taken of some microstructured, uncoated or plasma coated samples during the wetting by a water drop containing a fluorescent dye. These images show the Wenzel state or a mixed wetting state by visualization of the interface between the water droplet and the surface. A new icing test chamber and a test setup were developed for characterization of the ice adhesion and the icing behavior. The tensile ice adhesion was measured at -20 °C by pull-off of ice cylinders (highly purified water, (<0.056 µS/cm, diameter of 4 mm, similar to the diameter of large raindrops) and compared to the theoretical values and the wetting behavior. The technical material surfaces measured for comparison showed a high ice adhesion, which led to cohesive fractures especially on the metal surfaces, whereas some of the commercial anti-ice coatings showed lower ice adhesion values. The flat, plasma coated PU surfaces showed adhesive fractures with a reduced ice adhesion compared to the technical material surfaces and uncoated PU and revealed a good correlation of the ice adhesion with the wetting behavior of water (work of adhesion). On the other hand, the microstructured PU surfaces showed a greatly increased ice adhesion in comparison to the flat PU and technical material surfaces which was enhanced even further by the plasma coatings and did not correlate with the wetting behavior. The reason for this is the wetting transition from the Cassie-Baxter to the Wenzel state during the cooling or freezing process, leading to an increased ice-surface contact area and mechanical interlocking of the ice with the micro- and nanostructures. The freezing of water drops was examined in thermodynamic equilibrium (static experiment) and under quasi-steady conditions (dynamic experiment). In the static experiment, 15 µl water drops (corresponding to medium to large raindrops) at room temperature were dispensed onto a cold surface at a constant temperature of -20 °C. The freezing delay times, the crystallization times and the total freezing times were measured and compared to calculated expected values. On the flat samples, the freezing delay times could be extended by the plasma treatments. On the microstructured samples, the freezing (nucleation) could sometimes be delayed even further, but not always reproducible because of an unstable Cassie-Baxter state. In the dynamic experiment, 25 µl water drops (corresponding to large raindrops) were cooled down in quasi-steady conditions with the surface and the surrounding atmosphere by a constant, low cooling rate of 1 K/min while the water drop temperature was measured by an IR camera for determination of the surface-specific nucleation temperature and crystallization time. A lower nucleation temperature could be measured on the flat, plasma coated PU surfaces compared to uncoated PU and the hydrophilic glass and metal surfaces. The superhydrophobic PU surfaces did not show a further reduction of the nucleation temperature because of an unstable Cassie-Baxter state. The resulting measured nucleation temperatures were compared to the expected values calculated with an enhanced nucleation theory including a quasi-liquid interfacial layer of the ice nucleus and a Poisson process. Overall, it is shown that hot embossing and PECVD are useful processes for creating superhydrophobic PU surfaces with regard to a roll-to-roll process. The flat, plasma coated PU films show a reduced ice adhesion and lowered nucleation temperature compared to the relevant technical material surfaces. The microstructured, plasma coated PU films are far more water repellent than the flat, plasma coated PU surfaces or the other technical materials. However, the microstructures with base diameters of 35 µm or more and the nanoroughness of the plasma coatings cannot stabilize the Cassie-Baxter state of a freezing water drop enough for a low ice adhesion or a significant decrease of the nucleation temperature. These superhydrophobic PU films are therefore not more icephobic than the flat, plasma coated PU films. In the outlook, the reduction of the geometrical parameters of the microstructures (diameter D, distance P) and nanostructures (curvature radius R) of the surface functionalizations for lower ice adhesion values and nucleation temperatures is proposed.Item Open Access Elektrochemische, spektroskopische und strukturelle Eigenschaften von Platin- und Rheniumverbindungen mit N-Donor-Liganden(2019) Bauer, Sonja; Kaim, Wolfgang (Prof. Dr.)Der erste Teil der Arbeit befasst sich mit einer Reihe neuer Trimethylchloroplatin(IV)-Verbindungen mit verschiedenen redoxaktiven Azobispyridin-Derivaten (abpy-R). Durch den Einbau von elektronenziehenden Substituenten an den abpy-Liganden werden die π*-Orbitale energetisch abgesenkt und die Auswirkungen dieses Effektes auf die elektronische Struktur sowie auf die spektroskopischen und elektrochemischen Eigenschaften der Verbindungen werden aufgeklärt. Der zweite Teil beschäftigt sich mit Tricarbonylchlororhenium(I)-Verbindungen mit Bis(arylimino)acenaphthen - Liganden (BIAN). Durch elektrochemische und spektroskopische Methoden wird ein genaueres Verständnis der elektronischen Struktur und der Redoxprozesse dieser Verbindungen erhalten. Besonders der Einfluss von elektronenziehenden gegenüber elektronenschiebenden Substituenten am Liganden auf das Elektronentransferverhalten der Komplexe wird untersucht. Der dritte Teil der Arbeit behandelt Dimesitylplatin(II)-Verbindungen mit verschiedenen sterisch zunehmend anspruchsvollen N-Donor-Liganden. Dabei wird neben dem Elektronentransferverhalten der Verbindungen besonders der Einfluss der zusätzlichen sterischen Abschirmung durch die N-Donor-Liganden auf die Stabilität der Komplexe, speziell der oxidierten Verbindungen, untersucht.Item Open Access Generierung von gesättigten N-Heterozyklen mit Iminreduktasen(2019) Borlinghaus, Niels; Hauer, Bernhard (Prof. Dr.)
- «
- 1 (current)
- 2
- 3
- »