Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
Search Results
Item Open Access Misfit-layered cobalt oxides for thermoelectric energy conversion(2017) Büttner, Gesine; Weidenkaff, Anke (Prof. Dr.)The conversion of waste heat into electrical current by a thermoelectric converter can significantly contribute to a more sustainable usage of our resources. The p-type misfit-layered [Ca2CoO3-δ][CoO2]1.62 is known for its promising conversion efficiency, which yet needs to be improved significantly for commercial applications. The efficiency of a material increases with the Figure of Merit ZT=σα^2/κ, with Seebeck coefficient α, electrical conductivity σ, and thermal conductivity κ. The aim of this thesis is to provide a better understanding of the electrical and the thermal properties of the complex [Ca2CoO3 δ][CoO2]1.62 and to use this understanding to improve the efficiency of converters. Accordingly, (i) the increase of ZT via cation substitution is shown; (ii) a better understanding of the electrical transport above room temperature is developed; (iii) the effect of stoichiometric defects and secondary phases on the thermoelectric properties is investigated. Finally, (iv) [Ca2CoO3 δ][CoO2]1.62 - CaMn0.97W0.03O3 δ - converters are fabricated and the efficiency is increased by a suitable converter design. More specifically, the unexplored influence of Ru and In substitution on the thermoelectric properties of the polycrystalline [Ca2CoO3 δ][CoO2]1.62 is investigated. While In does not have a positive effect, Ru for Co substitution increases ZT up to 20 %. This increase stems from a strong reduction of the thermal conductivity - which is probably induced by resonance scattering - while the decrease of the power factor α^2 σ is minor. The electrical transport mechanism of pure and Ru-substituted [Ca2CoO3 δ][CoO2]1.62 between room temperature and 800 K so far lacks a coherent theoretical model. Surprisingly, the framework of Anderson localization, which was developed to describe conduction in an impurity band of semiconductors, can be applied to the oxide. The Anderson model assumes that transport happens via charge-carrier hopping in a random Coulomb potential. For [Ca2CoO3 δ][CoO2]1.62, charges are considered to hop between Co sites in the CoO2 layer, while the random potential originates from interactions with the mismatched Ca2CoO3 δ layer. The presence of the ionized Ru atoms further alters the Coulomb potential, which increases the activation energy of the transport behavior. This understanding might contribute to the development of better theoretical models for the prediction of the thermoelectric properties of substituted [Ca2CoO3 δ][CoO2]1.62 compounds. A further improvement of the materials efficiency can be achieved by systematic introduction of stoichiometric defects and impurity phases. Here, the unexplored influence of the Co/Ca ratio on the thermoelectric properties of [Ca2 wCoO3 δ][CoO2]1.62, and the effect of Co3O4 impurity phase are investigated. It is shown that an increasing Co/Ca ratio in the [Ca2 wCoO3 δ][CoO2]1.62 phase leads to a larger figure of merit ZT induced by a strong resistivity drop. The decrease of resistivity stems from additional p-type charge carriers created by the formation of Ca vacancies. The Co3O4 impurity phase increases the thermal conductivity of the composite samples and leads to a reduction of ZT when the volume fraction of the Co3O4 phase is increased from 1% to 3%. Hence, the best figure of merit is expected close to the upper phase boundary of the [Ca2 wCoO3 δ][CoO2]1.62 phase. Not only the figures of merit of the materials, but also the design of a thermoelectric converter determines the device efficiency. In a converter, a p-type and a suitable n-type thermoelectric material are connected electrically in series and thermally in parallel. Here, [Ca2 wCoO3 δ][CoO2]1.62 is combined with the n-type CaMn0.97W0.03O3-δ and the device efficiency is improved by a variation of the ratio A_p/A_n of the cross section areas of the legs. The good agreement between the experimental values and the predictions of the compatibility model show the high quality of the fabricated devices and the value of the model for the optimization of the converter design. The adjustment of A_p/A_n improves the power output and the efficiency of the converters, where the best volume and area power densities exceed published high temperature values. The achieved efficiency of 1.08 % at a temperature of 1085 K at the hot side is close to the theoretical expected efficiency and can be further improved via ZT.Item Open Access Electronic transport properties of DNA sensing nanopores : insight from quantum mechanical simulations(2017) Sivaraman, Ganesh; Fyta, Maria (Jun.-Prof. Dr.)The translocation of DNA through nanopores is an intensively studied field as it can lead to a new perspective in DNA sequencing. During this process the DNA is electrophoretically driven through a nanoscale hole in a membrane, and use different sensing schemes to read out the sequence. Within the scope of nanopore sequencing two important sensing schemes relevant to this thesis are: 1.) Tunneling sequencers based on solid state nanopores embedded with gold electrodes 2.) 2D materials beyond graphene For scheme 1, an obvious improvement is to coat the gold electrode with molecules that have high conductance and can form instantaneous hydrogen bond bridges with the translocating polynucleotide thereby improving the transverse current signal. The molecule that we propose is the so called diamondoid which are diamond caged molecules with hydrogen termination. Before applying such a molecule to a nanopore electrode set up, one would like to understand their interaction with DNA and its nucleobases. For this purpose, hydrogen bonded complexes formed between nitrogen doped derivatives of smallest diamondoids (i.e. adamantane derivatives) and nucleobases were investigated using dispersion corrected density functional theory (DFT). Mutated and methylated nucleobases are also taken into consideration in these investigations. DFT calculations revealed that hydrogen bonds are of moderate strength. In addition, starting from the DFT predicted hydrogen bonding configuration for each complex, rotations, and translations along a reference axis was performed to capture variations in the interaction energies along the donor-acceptor groups of the hydrogen bonds. The electronic density of states analysis for the hydrogen bonded complexes revealed distinguishable signatures for each nucleobase, thereby showing the suitability for application in electrodes functionalised with such probe molecules. In the next step, an adamantane derivative is placed on one of the electrode and nucleotides are introduced in such a way that nucleobases form hydrogen bonds with the of the nitrogen group of the adamantane derivatives. Electronic transport calculations were performed for gold electrodes functionalised with 3 different adamantane derivatives. Four pristine nucleotides, one mutated, and one methylated nucleotides were considered. Analysis of the transmission spectra reveal that each of the nucleotides has a unique resonance peak far below the Fermi level. We have also proposed a gating voltage window to sample the resonance peaks of the nucleotide so that they can be distinguished from each other. An alternative to tunneling sequencers would be to use nanopores built in to ultra thin metallic nanoribbons such as graphene. The sequence can be read out from the in-plane current modulation resulting from the local field effect of the translocating nucleotides in the vicinity of the metallic pore edges. But the hydrophobicity of graphene makes it a difficult candidate in aqueous environment. Hence in scheme 2, the aim is to model an ultra thin material that can rectify the hydrophobicity of graphene and can be a very good candidate for current modulation sequencing. Ultra thin MoS2 (2H) monolayer exist as direct band gap semiconductor. Nanopores based on 2H phases have been reported in the literature and are not hydrophobic. By means of chemical exfoliation of the 2H phase, a meta stable 1T phase of MoS2 has also been synthesized by various experimental groups. The 1T phase of MoS2 is metallic. The aim of this thesis is to model a nano-biosensor template based on a hybrid MoS2 monolayer made up of a metallic (1T) phase sandwiched between semiconducting (2H) phase. The sensor that we propose, should have only metallic nanopore edges. As a first step, we have modeled the semiconductor-metal interface, and compared them with experiments. Then an investigation to understand the influence of the increase of the metallic unit on the electronic properties is performed. Since, point defects are highly relevant to electrochemical pore growth, a point sulfur defect analysis is provided to ascertain the weakest point in the sheet. Finally to understand the effect of the interface electronic transport calculations are performed. The transmission spectra reveals a clear asymmetry in the current flow across the interface by means of gating. In the end, the relevance of such a hybrid MoS2 material for nanopore sequencing is discussed.