Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
5 results
Search Results
Item Open Access Wetting, de-icing and anti-icing behavior of microstructured and plasma-coated polyurethane films(2019) Grimmer, Philipp E. S.; Hirth, Thomas (Prof. Dr. rer. nat.)Ice build-up on surfaces, for example on wings of airplanes or on rotor blades of wind turbines, impairs the functionality of transportation vehicles or technical systems and reduces their safety. Therefore, functional anti-ice surfaces are being researched and developed, which shall enable an easy removal or reduce the amount of ice on the surfaces at risk. The starting hypothesis for this work is that superhydrophobic polyurethane (PU) films with microstructure base diameters of 35 µm or more reduce the wetting by water, show a low ice adhesion for easy removal of ice and reduce or delay icing. Superhydrophobic PU films for passive anti- and de-icing were created by hot embossing and plasma enhanced chemical vapor deposition (PECVD). The hot embossing process as well as the plasma coating and etching processes were analyzed for the dependence of the surface characteristics on different process parameters. The functionalized PU films were characterized for their surface topography, surface chemistry, stability against erosion, wettability, ice adhesion and icing behavior. For comparison, the ice adhesion and icing behavior were examined on relevant technical materials (aluminum, titanium, copper, glass, epoxy resin of carbon fiber reinforced polymer and other fluoropolymers) and on some commercial anti-ice coatings. The PU films were chemically analyzed by IR spectroscopy. As the first process step for functionalization, microstructures of cylindrical, elliptical or linear shape were imprinted in PU films by a hot embossing technique with different ns-pulsed laser-drilled stamps and characterized by several microscopy methods. The microstructures had heights of 15 µm to 140 µm, diameters or widths of 35 µm to 300 µm and distances (pitch values) of 50 µm to 500 µm. The embossing process was analyzed and optimized in terms of the process parameters temperature, pressure, time, PU film release temperature and reproducibility of the microstructures. In a second functionalization step (PECVD) the microstructured surfaces were coated with thin, hydrophobic plasma polymers using different fluorocarbon precursors (CHF3, C3F6 and C4F8) or hexamethyldisiloxane (HMDSO). Different process parameters for plasma coating and etching (Ar or O2 plasmas) were used in order to create various nanoscale roughness values. Electron spectroscopy for chemical analysis (ESCA), spectroscopic ellipsometry and atomic force microscopy (AFM) were used for analysis of the chemical composition, the thickness and the nanoroughness of the plasma polymers. The functionalizations, especially the plasma coatings, were completely worn off by a UV/water weathering test (1000 h, X1a CAM 180 Test, SAE J-2527), but showed sufficient stability against sand erosion (DIN 52348), in a long-term outdoor test for 13.5 months and against fivefold repeated pull-off of ice. The silicone-like plasma coatings were more stable than the fluorocarbon plasma coatings. The wetting behavior of water was determined by static, advancing and receding contact angle measurements. Static contact angle measurements with diiodomethane (DIM) were made for determination of the surface free energies of the relevant surfaces. Advancing contact angles of over 150° and very low contact angle hysteresis values below 10° were reached on some of the cylindrically and elliptically structured PU samples with microstructure base diameters in the range of 35 µm to 50 µm. The measured water advancing contact angles did not reach the theoretical values of the Cassie-Baxter state. Starting from a mixed wetting state near Cassie-Baxter in case of the superhydrophobic PU surfaces, they approached the Wenzel state with an increasing pitch/diameter (P/d) factor. Fluorescence laser scanning microscopy images were taken of some microstructured, uncoated or plasma coated samples during the wetting by a water drop containing a fluorescent dye. These images show the Wenzel state or a mixed wetting state by visualization of the interface between the water droplet and the surface. A new icing test chamber and a test setup were developed for characterization of the ice adhesion and the icing behavior. The tensile ice adhesion was measured at -20 °C by pull-off of ice cylinders (highly purified water, (<0.056 µS/cm, diameter of 4 mm, similar to the diameter of large raindrops) and compared to the theoretical values and the wetting behavior. The technical material surfaces measured for comparison showed a high ice adhesion, which led to cohesive fractures especially on the metal surfaces, whereas some of the commercial anti-ice coatings showed lower ice adhesion values. The flat, plasma coated PU surfaces showed adhesive fractures with a reduced ice adhesion compared to the technical material surfaces and uncoated PU and revealed a good correlation of the ice adhesion with the wetting behavior of water (work of adhesion). On the other hand, the microstructured PU surfaces showed a greatly increased ice adhesion in comparison to the flat PU and technical material surfaces which was enhanced even further by the plasma coatings and did not correlate with the wetting behavior. The reason for this is the wetting transition from the Cassie-Baxter to the Wenzel state during the cooling or freezing process, leading to an increased ice-surface contact area and mechanical interlocking of the ice with the micro- and nanostructures. The freezing of water drops was examined in thermodynamic equilibrium (static experiment) and under quasi-steady conditions (dynamic experiment). In the static experiment, 15 µl water drops (corresponding to medium to large raindrops) at room temperature were dispensed onto a cold surface at a constant temperature of -20 °C. The freezing delay times, the crystallization times and the total freezing times were measured and compared to calculated expected values. On the flat samples, the freezing delay times could be extended by the plasma treatments. On the microstructured samples, the freezing (nucleation) could sometimes be delayed even further, but not always reproducible because of an unstable Cassie-Baxter state. In the dynamic experiment, 25 µl water drops (corresponding to large raindrops) were cooled down in quasi-steady conditions with the surface and the surrounding atmosphere by a constant, low cooling rate of 1 K/min while the water drop temperature was measured by an IR camera for determination of the surface-specific nucleation temperature and crystallization time. A lower nucleation temperature could be measured on the flat, plasma coated PU surfaces compared to uncoated PU and the hydrophilic glass and metal surfaces. The superhydrophobic PU surfaces did not show a further reduction of the nucleation temperature because of an unstable Cassie-Baxter state. The resulting measured nucleation temperatures were compared to the expected values calculated with an enhanced nucleation theory including a quasi-liquid interfacial layer of the ice nucleus and a Poisson process. Overall, it is shown that hot embossing and PECVD are useful processes for creating superhydrophobic PU surfaces with regard to a roll-to-roll process. The flat, plasma coated PU films show a reduced ice adhesion and lowered nucleation temperature compared to the relevant technical material surfaces. The microstructured, plasma coated PU films are far more water repellent than the flat, plasma coated PU surfaces or the other technical materials. However, the microstructures with base diameters of 35 µm or more and the nanoroughness of the plasma coatings cannot stabilize the Cassie-Baxter state of a freezing water drop enough for a low ice adhesion or a significant decrease of the nucleation temperature. These superhydrophobic PU films are therefore not more icephobic than the flat, plasma coated PU films. In the outlook, the reduction of the geometrical parameters of the microstructures (diameter D, distance P) and nanostructures (curvature radius R) of the surface functionalizations for lower ice adhesion values and nucleation temperatures is proposed.Item Open Access Misfit-layered cobalt oxides for thermoelectric energy conversion(2017) Büttner, Gesine; Weidenkaff, Anke (Prof. Dr.)The conversion of waste heat into electrical current by a thermoelectric converter can significantly contribute to a more sustainable usage of our resources. The p-type misfit-layered [Ca2CoO3-δ][CoO2]1.62 is known for its promising conversion efficiency, which yet needs to be improved significantly for commercial applications. The efficiency of a material increases with the Figure of Merit ZT=σα^2/κ, with Seebeck coefficient α, electrical conductivity σ, and thermal conductivity κ. The aim of this thesis is to provide a better understanding of the electrical and the thermal properties of the complex [Ca2CoO3 δ][CoO2]1.62 and to use this understanding to improve the efficiency of converters. Accordingly, (i) the increase of ZT via cation substitution is shown; (ii) a better understanding of the electrical transport above room temperature is developed; (iii) the effect of stoichiometric defects and secondary phases on the thermoelectric properties is investigated. Finally, (iv) [Ca2CoO3 δ][CoO2]1.62 - CaMn0.97W0.03O3 δ - converters are fabricated and the efficiency is increased by a suitable converter design. More specifically, the unexplored influence of Ru and In substitution on the thermoelectric properties of the polycrystalline [Ca2CoO3 δ][CoO2]1.62 is investigated. While In does not have a positive effect, Ru for Co substitution increases ZT up to 20 %. This increase stems from a strong reduction of the thermal conductivity - which is probably induced by resonance scattering - while the decrease of the power factor α^2 σ is minor. The electrical transport mechanism of pure and Ru-substituted [Ca2CoO3 δ][CoO2]1.62 between room temperature and 800 K so far lacks a coherent theoretical model. Surprisingly, the framework of Anderson localization, which was developed to describe conduction in an impurity band of semiconductors, can be applied to the oxide. The Anderson model assumes that transport happens via charge-carrier hopping in a random Coulomb potential. For [Ca2CoO3 δ][CoO2]1.62, charges are considered to hop between Co sites in the CoO2 layer, while the random potential originates from interactions with the mismatched Ca2CoO3 δ layer. The presence of the ionized Ru atoms further alters the Coulomb potential, which increases the activation energy of the transport behavior. This understanding might contribute to the development of better theoretical models for the prediction of the thermoelectric properties of substituted [Ca2CoO3 δ][CoO2]1.62 compounds. A further improvement of the materials efficiency can be achieved by systematic introduction of stoichiometric defects and impurity phases. Here, the unexplored influence of the Co/Ca ratio on the thermoelectric properties of [Ca2 wCoO3 δ][CoO2]1.62, and the effect of Co3O4 impurity phase are investigated. It is shown that an increasing Co/Ca ratio in the [Ca2 wCoO3 δ][CoO2]1.62 phase leads to a larger figure of merit ZT induced by a strong resistivity drop. The decrease of resistivity stems from additional p-type charge carriers created by the formation of Ca vacancies. The Co3O4 impurity phase increases the thermal conductivity of the composite samples and leads to a reduction of ZT when the volume fraction of the Co3O4 phase is increased from 1% to 3%. Hence, the best figure of merit is expected close to the upper phase boundary of the [Ca2 wCoO3 δ][CoO2]1.62 phase. Not only the figures of merit of the materials, but also the design of a thermoelectric converter determines the device efficiency. In a converter, a p-type and a suitable n-type thermoelectric material are connected electrically in series and thermally in parallel. Here, [Ca2 wCoO3 δ][CoO2]1.62 is combined with the n-type CaMn0.97W0.03O3-δ and the device efficiency is improved by a variation of the ratio A_p/A_n of the cross section areas of the legs. The good agreement between the experimental values and the predictions of the compatibility model show the high quality of the fabricated devices and the value of the model for the optimization of the converter design. The adjustment of A_p/A_n improves the power output and the efficiency of the converters, where the best volume and area power densities exceed published high temperature values. The achieved efficiency of 1.08 % at a temperature of 1085 K at the hot side is close to the theoretical expected efficiency and can be further improved via ZT.Item Open Access Nanomechanische und nanoelektrische rasterkraftmikroskopische Analyse von Polymerelektrolytbrennstoffzellen(2022) Morawietz, Tobias; Friedrich, K. Andreas (Prof. Dr. rer. nat.)Die vorliegende Arbeit beschäftigt sich mit der Analyse von Brennstoffzellenkomponenten. Dabei wird der Fokus dieser Arbeit auf die Analyse der katalytischen Schichten mit dem Rasterkraftmikroskop gelegt. Das Rasterkraftmikroskop kann Strukturen mit wenigen Nanometern auflösen und dabei die materialspezifischen Eigenschaften aufzeichnen. Der Einsatz und die Weiterentwicklung von Rasterkraftmikroskop basierten Messmethoden für diesen Anwendungszweck wird in dieser Arbeit dargelegt. Die (Nano)-Struktur von vielen Brennstoffzellenkomponenten konnte mit den bisherigen verwendeten Methoden nicht vollständig aufgeklärt werden. Vor allem die Struktur des Ionomers innerhalb der Elektrode ist eine Unbekannte. Über das materialsensitive Rasterkraftmikroskop kann die Identifikation und Strukturanalyse der einzelnen Komponenten der katalytischen Schichten erfolgen. Die Struktur und die mechanischen und elektrischen Eigenschaften des Ionomers in der Elektrode ist für den Massentransport und die ionische/elektronische Leitfähigkeit von Bedeutung. Um die Eigenschaften des Ionomers in den Elektroden zu beschreiben, wurde die Nanostruktur des Polymerelektrolyten auf verschiedenen Größenskalen untersucht. Es werden in dieser Arbeit ultra-dünne Schichten und deren Eigenschaften, sowie die Ausbildung von Grenzschichten zur Gasphase beschrieben. Ausgegangen wird von der Struktur einzelner Ionomerbündel welche auf verschiedene Substrate abgesetzt wurden. Die Struktur dieser Primärstrukturen und die Ausbildung erster Schichten werden für Ionomere mit unterschiedlichem Äquivalentgewicht beschrieben. Es wurden eine minimale Bündelhöhe von 1,5 nm und ein lamellarer Aufbau von den Schichten gemessen. Die Bündelhöhe wird in Abhängigkeit von Temperatur und relativen Luftfeuchte dargestellt. Ultra-dünne Ionomerschichten wurden als Model für Schichten in den Elektroden hergestellt. Als Ultra-dünne Schichten werden Schichten bezeichnet, welche eine Dicke kleiner als 100 nm besitzen. Sehr dünne Schichten (< 12 nm) zeigten in den Messungen keine oder nur sehr geringe ionische Leitfähigkeit durch die Schicht. Mit katalytisch aktiven AFM Spitzen wurde eine Querleitfähigkeit dieser sehr dünnen Schichten und eine Schichtdickenabhänigkeit der Ionenleitfähigkeit nachgewiesen. Dickere Schichten über einen Mikrometer wurden über ein Tauchziehverfahren erzeugt, um die Ausbildung der kristallinen Bereiche sowie der Grenzphase zur Gasphase von Membranen mit bekannter Vorgeschichte zu beschreiben. In den Messungen zeigten sich Bereiche mit erhöhter Steifigkeit. Die Messungen der Steifigkeit konnte eine Proportionalität zur mit Dynamische Differenzkalorimetrie gemessenen Kristallinität der Ionomere gezeigt werden. Die Kristallinität nahm mit zunehmendem Äquivalentgewicht und Alter der Schichten zu. Die Untersuchungen der katalytischen Schichten mit dem Rasterkraftmikroskop zeigten einen deutlichen Kontrast in den Materialeigenschaften der katalytischen Schichten zwischen dem Ionomer und dem Katalysator. Dabei kann die Struktur sehr hoch aufgelöst vermessen werden. Je nach verwendeter Spitze liegt die laterale Auflösung zwischen 1-25 nm. Das Ionomer konnte durch höhere Adhäsion und Deformation, eine niedrigere Steifigkeit sowie keinen elektronischen Strom identifiziert werden. An Messungen der Oberfläche wurden die Bereiche, die den Katalysator umhüllen, sowie größere zusammenhängende Ionomerbereiche gemessen. An Mikrotom-Querschnitten, wurden in den katalytischen Schichten Ionomerschichten in einer Größe gefunden, die auch durch die ultra-dünnen Schichten als Modellelektroden erzeugt werden konnten. Diese Ionomerschichten umhüllen die Katalysatorpartikel. Die Dicke der Schichten lag im Bereich von ~2,5 nm - 15 nm und war abhängig von der Temperatur und relativen Luftfeuchte. Außerdem scheint die Ionomerschichtdicke von dem Herstellungsverfahren abhängig zu sein. Nach Betrieb der Brennstoffzellen wurde eine Abnahme der Schichtdicke festgestellt. Ein Zusammenhang zwischen Ausgangsschichtdicke und irreversibler Degradationsrate durch den Brennstoffzellenbetrieb wurde gezeigt. Nach Betrieb wurde über Rasterelektronenmikroskop-Messungen unterstützend eine Abnahme der Elektroden- und Membrandicke gemessen. Eine Abnahme des Gesamtionomers konnte über das Rasterkraftmikroskop, Energiedispersive Röntgenspektroskopie und Infrarotspektroskopie gezeigt werden. In der Membran bildete sich nach Betrieb ein Platinband, welches von der Position der Probe in der Membran Elektroden Einheit abhängig war. Eine Korrelation zwischen Degradationsrate und Ablagerung von Platin in der Membran konnte gezeigt werden. Die Ablagerung kann in sehr großem Ausmaß stattfinden, dass Kurzschlüsse durch die Membran festgestellt werden konnten, welche mit dem Rasterkraftmikroskop nachgewiesen werden konnten. In der Bildanalyse Software GeoDict wurden Modelle von den Elektroden nach den gemessenen Daten erstellt und verschiedene Faktoren, wie Ionomerschichtdicke, Katalysatordurchmesser und Bedeckung des Katalysators mit Ionomer auf die resultierende ionische und elektronische Leitfähigkeit untersucht. Zusammenfassend trägt diese Arbeit zur Aufklärung der Struktur und Eigenschaften von Polymerelektrolytbrennstoffzellen bei und zeigt Degradationsmechanismen auf.Item Open Access Scale-up of gas fermentations : modelling tools for risk minimisation(2020) Siebler, FloraThe reduction of greenhouse gas emissions is a global endeavour supported by society, politics and industry. In recent years, circular economy, reducing the exploitation of fossil energy sources, have increased the demand for new solutions when producing commodities and fine chemicals. Caboxydotrophic fermentations with acetogenic bacteria are potential processes in order to reach these goals. They convert gaseous substrates such as CO, and CO2/H2 mixtures. However, gases as sole substrate are rather challenging, not only in small lab-scales but especially in large-scale. Transferring an efficient fermentation process from experimental to industrial scales often results in unpredictable performance losses. This study presents an in silico concept minimising possible risks in gas fermentations up-scaling. First, the economical feasibility of various fermentation methods is investigated. Then, two computational tools are presented using Clostridium ljungdahlii as model organism and synthesis gas as substrate in a 125 m3 bubble column reactor. The combination of economical investigation with modelling tools show high potential for successful scale-up of gas fermentations. With this concept feasibility, reactor design, operation mode and general risk minimisation can be analysed and specified.Item Open Access Fundamental understanding of inherent processes in magnesium-sulfur batteries(2024) Häcker, Joachim; Friedrich, K. Andreas (Prof. Dr. rer. nat.)In the face of climate change, the decarbonization of industry and everyday life has finally been declared a global goal in recent years, with energy storage in batteries playing a key role. These are needed for both, the decarbonization of vehicles and, in the long term, aviation, as well as in the stationary sector for grid stabilization due to day-night or seasonal fluctuations in renewable energy generation. On account of raw material shortages, lithium-based batteries alone, however, will not be capable to meet the global demand – thus alternative battery systems are tracking attention in the past decade. Among the various cell chemistries under research, magnesium-sulfur represent a promising electrochemical couple in terms of material abundance, high energy density, improved safety, good recyclability and low cost. Despite benefitting from the long-term research on lithium-sulfur batteries (Li-S), the magnesium-sulfur battery (Mg-S) is still in its infancy facing unique challenges and intrinsic limitations. This cumulative dissertation consists of five peer-reviewed scientific articles, which aim to shed light on different components and processes in a Mg-S battery constituting the main obstacles in its development, namely (i) the high ion charge density resulting in large desolvation energy, slow diffusion and impeded redox kinetics, (ii) the sulfur dissolution, self-discharge and polysulfide shuttle and (iii) the passivating surface layers on the Mg anode. Therefore, different attempts in terms of electrode manufacturing and operando characterization methods were pursued. Starting with an in-depth analysis of the first discharge cycle by means of electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS), the subsequent study applied operando UV/Vis spectroscopy and operando imaging to gain insights into the sulfur and polysulfide dissolution of different cathode compositions during the initial ten cycles. Identifying the magnesium anode and the processes at its electrolyte interface as crucial for the efficiency and capacity retention, the long-term cycling performance of pristine and coated Mg anodes was investigated over 150 cycles. Additionally, the influence of sulfur species on the interfacial processes of six different anode concepts could be determined in symmetrical and full cells applying operando EIS. In a concluding study, the transport properties of Mg cations in different separators were compared to their calcium and lithium counterparts. The main findings comprise a severe three-staged self-discharge governed by the sulfur reduction at the unprotected Mg surface and boosted by temperature. An artificial SEI coating is beneficial to not only mitigate the self-discharge, but also enhance the initial Coulombic efficiency and capacity retention. This is originated in mitigated parasitic reactions to form an in situ SEI, mainly consisting of MgF2, MgS and MgO, on the magnesium surface. Therein, hindering the reaction of sulfur species is particularly decisive to circumvent large interfacial resistances. On the cathode side, polar additives are beneficial to serve as adsorption and reaction centers, however with no long-term effect due to precipitates covering the surface. The kinetic of the sulfur redox reactions, which involve S8, S62- and S42- in the glyme-based Mg[B(hfip)4]2 electrolyte, are significantly enhanced by temperature indicating the sluggish MgS nucleation kinetics and Mg2+ solid diffusion. Its inherent high charge density further affects the magnesium cation transport in the electrolyte and its desolvation at the anode/electrolyte interface due to the rigid and strongly bound solvation shell. Consequently, in comparison to calcium and lithium, larger polarization overpotentials and separator tortuosities, respectively, were observed in the Mg system.