Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
20 results
Search Results
Item Open Access Entwicklung laserspektroskopischer Methoden zur Analyse der Verdunstungseigenschaften von Brennstofftropfen(Stuttgart : Deutsches Zentrum für Luft- und Raumfahrt, Institut für Verbrennungstechnik, 2021) Werner, Stefanie; Riedel, Uwe (Prof. Dr. rer. nat.)Die steigenden Emissionen des klimaschädlichen Treibhausgases CO2 durch die Verbrennung von fossilen, endlichen Energieträgern müssen möglichst schnell und nachhaltig reduziert werden. Ein vielversprechender Lösungsansatz zur Reduzierung der Schadstoffemissionen bei der Verbrennung liegt in dem Einsatz von alternativen und erneuerbaren Brennstoffen. Als Energieträger bieten sich auf Grund ihrer hohen Energiedichte vor allem flüssige Brennstoffe an. Diese werden typischerweise durch Druckzerstäubung in die Brennkammer eingebracht, verdunstet und dann mit dem Oxidationsmittel vermischt und verbrannt. Die Verdunstung der kleinen Brennstofftropfen des sogenannten Sprays ist von entscheidender Bedeutung für den Gesamtverbrennungsprozess in Verbrennungsmotoren und Gasturbinen. Im Allgemeinen bestimmt die Verdunstungsrate die Verbrennungsrate. Daher sind Modelle notwendig, die eine genaue Vorhersage der Brennstoffverdunstung ermöglichen. Zur Validierung dieser Modelle werden quantitative Messungen unter genau definierten Randbedingungen benötigt. Da die Prozesse in technischen Brennkammern sehr komplex sind, werden Experimente zur Tropfenverdunstung häufig mit linearen, monodispersen Tropfenketten durchgeführt, um die Kopplung zwischen den verschiedenen Effekten zu minimieren. Durch die geringe Größe der Tropfen (typischerweise wenige hundert Mikrometer oder weniger), erfordert die experimentelle Untersuchung eine hohe räumliche Auflösung. In dieser Arbeit wurden quantitative, laseroptische Messtechniken mit hoher räumlicher Auflösung zur experimentellen Untersuchung der Tropfenverdunstung an monodispersen Tropfenketten entwickelt. Mit den Messtechniken wurden Validierungsdaten für die Verdunstungseigenschaften von verschiedenen Brennstoffen bestimmt. Konzentrationsmessungen von verdunsteten Kohlenwasserstoffen wurden unter Verwendung von Infrarot-Laserabsorptionsspektroskopie und laserinduzierter Fluoreszenzspektroskopie (LIF) durchgeführt. Tropfenketten wurden mit einem Tropfenkettengenerator erzeugt, welcher vertikal in einem Strömungskanal installiert wurde. Die untersuchten Brennstoffe waren Cyclohexan, iso-Octan, n-Heptan, n-Pentan, 1-Butanol und Anisol. Der Strömungskanal wurde mit einer laminaren Luftströmung bei verschiedenen Temperaturen (313 K - 430 K) durchströmt. Da die untersuchten Tropfen einen Durchmesser in der Größenordnung von 120 bis 160 µm hatten und die Konzentrationsgradienten nahe der Tropfenoberfläche groß waren, war eine hohe räumliche Auflösung der Messtechniken erforderlich. Die Absorptionsmessungen wurden mit der Infrarotstrahlung eines HeNe-Lasers bei λ = 3,39 µm durchgeführt, um die CH-Streckschwingung der Kohlenwasserstoffe anzuregen. Die für die Quantifizierung der Brennstoffkonzentrationen benötigten Absorptionsquerschnitte wurden in einer beheizten Gaszelle für Temperaturen von 300 K - 773 K bestimmt. Die räumliche Auflösung im Strömungskanal betrug < 50 µm über eine Länge von 2 mm (Halbwertsbreite). Durch die Zylindersymmetrie und gute Stabilität der Tropfenketten konnten zeitliche Mittelungs- und Tomografieverfahren angewandt werden. Hierdurch konnten radiale Konzentrationsprofile an mehreren Positionen im Strömungskanal erhalten werden. Aus dem Anstieg der Dampfkonzentration an verschiedenen Messpositionen konnte die Verdunstungsrate bestimmt werden. Die Verdunstungsraten wurden in Abhängigkeit von der Mantelstromtemperatur (313 K - 430 K), der Tropfengeschwindigkeit (8 m/s - 23 m/s), der Tropfenerzeugungsfrequenz (12 kHz - 75 kHz) und dem Tropfenabstand (300 µm - 685 µm) gemessen. Im untersuchten Temperaturbereich steigt die Verdunstungsrate des Brennstoffs linear mit der Temperatur an. Die Reihenfolge der Brennstoffe in Bezug auf die Verdunstungsrate entspricht den Siedepunkten der einzelnen Brennstoffe. Da technische Brennstoffe häufig eine Mischung mehrerer Komponenten sind, ist die Untersuchung von Brennstoffgemischen von großem Interesse. Daher wurde ein Messverfahren entwickelt, um binäre Gemische zu untersuchen. Das Verfahren wurde verwendet, um eine Mischung aus Cyclohexan und Anisol zu untersuchen. Zwei Messtechniken - laserinduzierte Fluoreszenz (LIF) und Infrarot Absorptionsspektroskopie - wurden verwendet, um beide Spezies zu messen. Um λ = 3,39 µm ist der Absorptionsquerschnitt von Cyclohexan um etwa den Faktor 8 größer als von Anisol. Im untersuchten Fall war die Konzentration aufgrund des höheren Dampfdrucks ebenfalls deutlich größer. Daher konnte das Infrarot-Absorptionssignal praktisch ausschließlich Cyclohexan zugeordnet werden. Anisol hat bei Anregung bei λ = 266 nm eine sehr gute Fluoreszenzquantenausbeute, während Cyclohexan keine Fluoreszenz zeigt. LIF ermöglicht daher die Quantifizierung von Anisol (oder anderen Aromaten) ohne Interferenz durch Kohlenwasserstoffe. Es wurde ein Messverfahren entwickelt, welches Halationseffekte vermeidet, die typischerweise in planaren LIF-Experimenten an Tropfenketten auftreten. Kalibrationsmessungen, die im gleichen Strömungskanal durchgeführt wurden, ermöglichten die Quantifizierung der verdunsteten Anisolkonzentrationen. Die räumliche Auflösung betrug 80 µm. Ähnlich wie bei den Einzelkomponentenmessungen wurden Verdunstungsraten bestimmt. Wie aufgrund des niedrigeren Dampfdrucks zu erwarten, ist die Verdunstungsrate von Anisol niedriger als die von Cyclohexan. Die Verdunstungsrate von Cyclohexan in der binären Mischung stimmt gut mit den Einzelkomponentenmessungen überein. Das entwickelte Messverfahren ist sehr vielversprechend für weitere Untersuchungen an Mehrkomponentenmischungen. In dieser Arbeit konnte damit erstmals mit hoher räumlicher Auflösung die Verdunstung von Brennstoffkomponenten mittels Absorptionsspektroskopie in der Nähe von Brennstofftropfen untersucht werden. Zusätzlich wurden in Kombination mit laserinduzierter Fluoreszenzspektroskopie Messungen an binären Mischungen durchgeführt. Damit steht ein wertvoller Datensatz zur Validierung von numerischen Simulationen zur Verfügung.Item Open Access Spectroscopic investigations of the magnetic anisotropy of lanthanide- and cobalt-based molecular nanomagnets(2016) Rechkemmer, Yvonne; Slageren, Joris van (Prof. Dr.)Single-molecule magnets are metal complexes exhibiting an energy barrier for spin reversal, leading to magnetic bistability and slow relaxation of the magnetization. Their potential for practical applications such as high-density magnetic data storage was recognized early on and with the goal of achieving high energy barriers, different kinds of single-molecule magnets have been synthesized. The quadratic dependence of the barrier height on the spin motivated chemists to synthesize metal complexes with very high total spins; however, with limited success. It was shown that high spins come along with low anisotropies and increased interest thus focused on the synthesis and investigation of (mononuclear) complexes of highly anisotropic metal centers, e.g. lanthanide or cobalt complexes. Although rather high energy barriers can be achieved in such systems, practical application remains problematic and has not been realized yet. Reasons are for example the lack of rational design criteria and the complex interplay of different magnetic relaxation pathways. The aim of this work was therefore the comprehensive magnetic and spectroscopic investigation of selected molecular lanthanide and cobalt compounds in order to obtain a deeper insight into the correlation of molecular and electronic structures as well as the corresponding magnetic properties. The applied spectroscopic methods included electron paramagnetic resonance spectroscopy, far-infrared spectroscopy and optical methods. Special emphasis was placed on magnetic circular dichroism (MCD) spectroscopy, which served as a main tool for electronic structure determination. However, since the MCD-spectrometer was not part of the available experimental equipment at the University of Stuttgart, its design, setup and characterization were the first part of this work. In the further course of this work MCD-spectroscopy was employed for the electronic structure determination of selected lanthanide and cobalt compounds. The studied lanthanide compounds were literature-known molecular tetra-carbonates of erbium (1-Er) and dysprosium (1-Dy). Detailed magnetometric studies showed that both 1-Er and 1-Dy are field-induced single-molecule magnets; however, 1-Er and 1-Dy show significant differences in their magnetic relaxation behavior. The magnetic studies were complemented by detailed spectroscopic investigations.The combination of far-infrared-, luminescence- and MCD-spectroscopy allowed for the experimental determination of 48 energy levels for 1-Er and 55 levels for 1-Dy, which built the foundation for the subsequent crystal field analysis and electronic structure determination. In addition, the results of EPR-spectroscopic studies were used for fine-tuning and verifying the respectively determined crystal field parameters. Calculating the magnetic dipole strengths for transitions between the relevant states led to a quantitative understanding of the magnetic relaxation pathways. Besides the investigation of lanthanide compounds, this thesis deals with two classes of cobalt complexes. The first class comprises mononuclear complexes in which one Co(II) ion is ligated by the nitrogen donors of two doubly deprotonated 1,2-bis(methanesulfonamido)-benzene-ligands. Rather acute N-Co-N bite angles indicate strong deviations from ideal tetrahedral symmetry. The static magnetic properties hint at very high energy barriers for spin reversal and with the help of far-infrared spectroscopy, largely negative axial zero-field splitting parameters were determined. The corresponding energy barriers belong to the highest ever reported for 3d-transition metal complexes and investigating the dynamic magnetic properties confirmed single-molecule magnet behavior. The unique magnetic properties were fully explained by analyzing spectroscopic results. The MCD-spectra showed intense signals that were assigned to spin-allowed d-d-transitions. Subsequent crystal field analysis revealed that the strong axial crystal field generated by the ligands leads to a large splitting of the electronic terms and thus in turn to a relatively small energy gap between the electronic ground state and the first excited state. The resulting increase in second-order spin-orbit coupling explains the high energy barriers observed in the studied complexes. The second class of cobalt compounds studied in this work included dimers of distorted octahedrally coordinated Co(II) ions bridged by symmetrical or asymmetrical quinone based bridging ligands. The main focus of investigation lay on the impact of the bridging ligand on the magnetic coupling between the cobalt centers. Thus, the magnetic properties of the complexes were studied with the help of static susceptibility and magnetization measurements and analyzed by means of different models. Depending on the bridging ligand, different signs for the exchange coupling constants were found. The varying signs can be explained by different relative contributions of possible exchange paths, influenced by the different substituents at the bridging ligands or slight geometry differences. The observations indicate that electron withdrawing substituents favor ferromagnetic couplings, which are preferred in the context of molecular magnetism. All in all, it can be concluded that this work provides a contribution to the deeper understanding of the features relevant for single-molecule magnets. The electronic structure determination for selected lanthanide and cobalt complexes applying advanced magnetometric and spectroscopic techniques not only led to an understanding of the static and dynamic magnetic properties but also allowed for the development of design criteria and new approaches for improved single-molecule magnets in the future.Item Open Access Modeling and simulation of closed low-pressure adsorbers for thermal energy storage(2019) Schäfer, Micha; Thess, André (Prof. Dr. rer. nat.)Closed low-pressure adsorption systems can be applied for thermal energy storage. Their performance is determined by the mass and heat transport processes in the adsorber. Therefore, thorough knowledge of these transport processes is required for further storage development. The present thesis contributes to this by providing detailed models of closed low-pressure adsorbers and by conducting simulations over a broad range of parameters and configurations. The focus is on adsorbers of larger scale (length L = 0.1 . . . 1 m) and on the discharging process. As the adsorption pair, binderless zeolite 13X with water is examined. The models are developed in a stepwise manner from pore to storage scale. The Finite-Difference-Method is implemented to numerically solve the models. Simulations are conducted for defined reference cases as well as over a broad range of geometric and process parameters. The reference cases are analyzed in detail to gain a better understanding of the transport processes. Furthermore, the results are analyzed with respect to two particular modeling aspects: equilibrium assumptions and rarefaction effects (e. g. slip effect). With respect to the application, the discharging performance is analyzed in terms of thermal power and a defined discharging degree. Both the adsorber and the adsorbent configurations are varied. In addition, the effect of the discharging conditions is evaluated. Finally, one exemplary charging process is examined. The detailed analysis of the reference cases reveals that the mass and heat transport and the adsorption processes are strongly coupled and can only be understood in their interaction. For onedimensional adsorber configurations, that is the mass and heat transport are in the same direction, the discharging process is generally limited by the heat transport. This leads to insufficient thermal power and unsuitable discharging durations of up to one year. In contrast, for two-dimensional adsorber configurations, that is the mass and heat transport are in perpendicular directions, the discharging process can be limited either by the mass or heat transport or by the adsorption. The limitation depends on the configuration of the adsorber and adsorbent. Moreover, the twodimensional adsorber configurations can provide sufficient thermal power. With respect to the modeling, it is found that the assumption of a uniform pressure distribution is applicable for one-dimensional adsorber configurations. In contrast, for two-dimensional configurations, no equilibrium assumptions can be applied in general. However, for powder adsorbent it is always valid to assume local adsorption equilibrium. Regarding the rarefaction effects in twodimensional adsorber configurations with honeycombs and granules, the slip effect is relevant for small channel and particle diameters (d = 1 mm). For adsorbers with powder adsorbent, the reduction of the effective heat conductivity due to the rarefaction effect becomes relevant. With respect to the application, the variation of the adsorber configuration shows that the volumetric thermal power generally decreases with increasing adsorber length. Furthermore, the power decreases with increasing width between the parallel heat exchanger plates in the adsorber. Regarding the adsorbent configuration in two-dimensional adsorber configurations, it is found that the volumetric thermal power can be optimized by variation of the channel or particle diameter. Interestingly, the optima for peak and mean power do not coincide. In addition, the discharging degree is found to strongly depend on the discharging conditions in terms of discharging temperature and volume flow of the heat transfer fluid extracting the heat from the adsorber. In general, the discharging degree decreases with increasing discharging temperature. Similarly, the discharging degree decreases with increasing volume flow of the heat transfer fluid. Finally, the analysis of an exemplary charging process revealed that the pressure in the adsorber can increase significantly (> 50%) due to the desorption.Item Open Access Novel X-ray lenses for direct and coherent imaging(2019) Sanli, Umut Tunca; Schütz, Gisela (Prof. Dr.)Item Open Access Ion beam lithographic and multilayer fresnel zone plates for soft and hard X-rays: nanofabrication and characterization(2015) Keskinbora, Kahraman; Schütz, Gisela (Prof. Dr.)X-ray microscopy has become an important analytical characterization method for a plethora of applications in materials science, physics, chemistry and biology, thanks to the emergence of modern synchrotron radiation facilities. These facilities enable high brilliance, energy tunable, variable polarization X-rays which gives access to mass density, elemental, chemical, electronic and magnetic properties of materials. In the soft X-ray energies nearly all elements can be probed by spectromicroscopic methods. Another important property of synchrotron radiation is the time structure in the ns to ps range, which can be utilized for sophisticated time resolution studies. These opportunities can be combined with high spatial resolution which is determined by the focusing method and the optic. Focusing of X-rays has historically been a difficult task due to strong absorption and weak phase shift of X-rays within matter. The required phase shift of X-rays, which depends on the real part of the complex refractive index, differs from 1 (the vacuum refractive index) only on the order of 10^-2 to 10^-6 and conventional lenses do not work. One very successful X-ray optic is the Fresnel Zone Plate (FZP), a diffractive optic that act as a lens under certain conditions and can focus X-rays to nanometer sized spots. The resolution of the FZP depends on the width of the outermost zone and is highly correlated with the smallest feature that can be fabricated. Conventionally, the e-beam lithography (EBL) is used for production FZPs which could resolve up to 10 nm structures with serious limitations. One difficulty of EBL is its ever increasing complexity for many-step fabrication of smaller features or intricate geometries. Therefore, EBL is mostly constrained to planar, binary geometries with moderate efficiencies strongly decreasing with energy and not effective for hard X-rays. Special 3D geometries in the form of kinoform lenses can theoretically have 100 % focusing efficiencies. Attempts to approximate these geometries via EBL increased the number of process steps even further. The smallest FZP feature size even for low aspect ratios achievable via EBL is fundamentally limited due to the proximity effect which is the interaction and spread of electrons within the resist material. We addressed these issues by focusing our research on alternative FZP fabrication techniques as high-speed ion beam lithography (IBL), and gray scale ion lithography to realize efficient kinoforms. Another approach towards full-material multilayer FZPs with infinite aspect ratio was based on atomic layer deposition (ALD) with subsequent ion beam slicing. Each of these three methods targets specific challenges faced by the e-beam lithography based FZP fabrication techniques. All the fabricated FZPs were tested for their resolution and efficiency performances at a state of the art scanning transmission X-ray microscope at BESSY for soft X-rays and/or at optical test stations at ESRF and PETRA III for hard X-rays. Using IBL the rapid preparation of a 110 nm thick Au FZP with 50 µm diameter and 50 nm ∆r in less than 13 minutes is demonstrated. Employed for X-ray microscopy, the FZP clearly resolved 28.5 nm features with a cut-off of 24.3 nm at ~1120 eV. Additional process improvements were made towards smaller zones with higher zone quality. They allowed the preparation of a FZP with 30 nm outermost half-period remarkably, in about 8 min. This FZP was shown to clearly resolve 21 nm features on a multilayer test object with large room for improvement. This high through-put FZP production route is of special interest not only concerning the low cost and easy availability. A large array of these optical components is attractive, for experiments such as one-shot ultra-high brilliance FEL investigations due to the radiation damage or for instance for coded-aperture arrays for high-angle resolving X-ray astronomy. Towards fabrication of kinoforms for high efficiency X-ray focusing, we have performed various materials optimization studies in order to achieve a high surface quality optic. After various trials the materials were finally optimized and the fabricated lenses achieved more than 14 % absolute diffraction efficiency that is almost 90 % compared to the theoretical prediction. This confirms how closely we were able to replicate the ideal three dimensional surface relief structure for the first time. It was possible to carry out imaging with these lenses with half-pitch resolutions down to 60 nm. The kinoform lenses were tested at the soft X-ray range where a significant absorption is present in materials. These results also potentially pave the way for very high efficiency hard X-ray focusing which can in principle be utilized in laboratory based X-ray sources, X-ray astronomy and the new rising field of X-ray ptychography. To fabricate high resolution ML-FZPs, Al2O3/Ta2O5multilayers, deposited on a smooth glass optical fiber via atomic layer deposition using non-dedicated instruments were carefully cut-out, sliced and polished to a high quality surface finish using focused ion beams. Following the transfer of the slice to a TEM grid as holder the slices were polished to a high surface finish quality, also via a focused ion beam. Fabricated ML-FZPs were synchrotron tested using an in-house constructed 2-axis tilt stage specially designed for aligning ML-FZP with respect to the X-ray optical axis. The results showed that it was possible to resolve 21 nm features in direct imaging at 1200 eV and sub-30 nm focusing at 8 keV. This is the highest demonstrated resolving power for a multilayer type FZP, to date to the best of our knowledge. Results exhibit the potential for high-resolution hard X-ray focusing where this type of optics are especially efficient. For ultra-high resolution hard and soft X-ray imaging, with potentially achievable ∆r of a few nm is well below what can be achieved through any lithography method available today.Item Open Access Monodisperse highly ordered and polydisperse biobased solid foams(2018) Andrieux, Sébastien; Stubenrauch, Cosima (Prof. Dr.)The aim of this work was the synthesis of monodisperse highly ordered biobased polymer foams and a comparison with their polydisperse counterparts. We used the biobased and biodegradable polymer chitosan, which we cross-linked with genipin. The polymer foams were synthesised via foam templating, i.e. via a liquid foam whose continuous phase contains a polymer and can be solidified. In order to obtain monodisperse highly ordered polymer foams, one first has to generate monodisperse highly ordered liquid foam templates. We did so by using microfluidics, which allows to produce monodisperse liquid foams with bubble sizes from 200 µm to 800 µm and polydispersities below 5%. The monodisperse foams were collected outside of the microfluidic channels and left to self-order under the influence of gravity and confinement. We studied the kinetics of the cross-linking reaction to find the optimal storage conditions during cross-linking. Once cross-linked we freeze-dried the gelled foams to obtain solid chitosan foams. We compared the morphological properties of the solid foams with those of the liquid templates in order to test the efficiency of the developed templating route. We observed how modifying the cross-linking and drying conditions can strongly affect the morphology of the solid foams. The main issue was to maintain the key properties of the liquid foam template throughout the solidification process, namely the bubble size distribution, the structural order and the density. We then compared the synthesised monodisperse polymer foams with their polydisperse counterparts. Although easy foaming methods exist for the generation of polydisperse foams, they do not allow the control over the polydispersity. We thus used microfluidics to generate liquid chitosan foams with tunable polydispersities from below 5% up to 26%. Microfluidics allows to match the average bubble size and density of the polydisperse liquid chitosan foam with those of the monodisperse counterpart. After solidifying the liquid templates we obtained solid foams with controlled polydispersities and studied the in uence of the polydispersity on the mechanical properties. However, we observed that not the polydispersity but the foam density was the main parameter at play. Moreover, the solid chitosan foams had weak mechanical properties with elastic moduli below 100 kPa. To overcome this issue, we incorporated cellulose nanofibres to the original chitosan solution and followed the developed route for foam templating. We had to adapt the microfluidic parameters to account for the viscosity changes brought about by the nanofibres. However, we managed to produce monodisperse liquid foams having the same bubble size, i.e. ~300 µm, but different amounts of cellulose nanofibres. The cellulose content had a strong influence on the solid foam morphology in general and on the pore connectivity in particular.Item Open Access Deposition and characterization of multi-functional, complex thin films using atomic layer deposition for copper corrosion protection(2022) Dogan, Gül; Schütz, Gisela (Prof. Dr.)This thesis focuses on ALD thin film protection properties against corrosion of copper to develop an understanding of material interface properties and to develop novel thin films processes. This understanding is then applied to enhance materials with potential use in semiconductor devices. The main research objectives are listed below: Understanding corrosion protection properties of ALD thin films: - Development of protective thin films by combining different oxide layers - To characterize the protection properties at high temperatures and in aggressive environments, - To understand the interaction of copper and ALD protection layers when exposed to high temperatures, - Finding the optimum deposition parameters to achieve defect-free thin layers for best corrosion protection Application of ALD oxide thin films for copper corrosion protection in semiconductor devices: - Structuring the ALD thin films to make reliable interface for copper-copper interconnects with micromachining methods such as laser drilling and plasma etching - To remove ALD layers in a localized, selective way without degradation of the underlying copper layerItem Open Access Phase-space resolved decay rates of driven systems near the transition state(2020) Feldmaier, Matthias; Main, Jörg (Prof. Dr.)Die Bewegung einzelner Atome oder Moleküle bei chemischen Reaktionen lässt sich in vielen Fällen durch klassische Mechanik auf einer Born-Oppenheimer Potentialfläche beschreiben. Hierbei sind die Reaktanten oft durch eine Rang-1 Barriere von den Produkten getrennt. Eine solche Barriere ist durch einen instabilen Freiheitsgrad, die Reaktionskoordinate und eine gegebene Anzahl an stabilen Freiheitsgraden, die orthogonalen Moden, charakterisiert. Eine reagierende Trajektorie wird die Barriere meist in der Sattelregion, d. h. in einer direkten Umgebung des Sattels, überqueren. Diese Region fungiert als Flaschenhals für die Reaktion. Im Rahmen der Theorie der Übergangszustände (engl. transition state theory, TST) können Reaktionsraten über den Fluss reaktiver Trajektorien durch eine nur einmal durchstoßene Trennfläche (engl. dividing surface, DS) berechnet werden. Eine solche Trennfläche ist an der normal hyperbolischen invarianten Mannigfaltigkeit (NHIM) des Sattels verankert und trennt das System in Reaktanten und Produkte. Die NHIM ist dabei ein spezieller Unterraum des vollen Phasenraums und enthält Trajektorien, welche für alle Zeiten an die Sattelregion gebunden sind. Da diese Trajektorien somit weder zur Reaktanten- noch zur Produktseite gehören, bildet die NHIM einen Übergangszustand (engl. transition state, TS) der Reaktion. Für getriebene Systeme ist dieser zeitabhängig. In dieser Arbeit werden anhand eines zweidimensionalen, getriebenen Modellsystems mehrere Methoden zur Berechnung von NHIM und DS im Phasenraum vorgestellt. Basierend auf der Dynamik in einer direkten Umgebung der NHIM werden außerdem verschiedene Ansätze zur Berechnung des zugehörigen Zerfalls der Reaktantenpopulation nahe des TS diskutiert. Anschließend werden die vorgestellten Methoden auf ein realistischeres chemisches Modell angewandt, der getriebenen LiCN <-> LiNC Isomerisationsreaktion. Ein wichtiges Resultat hierbei ist, dass das externe Treiben dieses Systems einen großen Einfluss hat, sowohl auf die Dynamik von Trajektorien in der NHIM, als auch auf den zugehörigen Zerfall der Reaktantenpopulation nahe des TS.Item Open Access Calculation of pure substance and mixture viscosities using PCP-SAFT and entropy scaling(Stuttgart : Universität Stuttgart, Institut für Technische Thermodynamik und Thermische Verfahrenstechnik, 2020) Lötgering-Lin, Oliver; Gross, Joachim (Prof. Dr.-Ing.)Item Open Access Atom probe study on CuNi thin films : miscibility gap and grain boundary segregation(2023) Duran, Rüya; Schmitz, Guido (Prof. Dr. Dr. h. c.)In dieser Arbeit wurde die Lage der Mischungslücke, und die Korngrenzsegregation im Legierungssystem, Kupfer-Nickel, per Atomsondentomographie (APT) analysiert. Zur Untersuchung der Mischungslücke eines binären Systems mit langsamer Diffusion wurde ein neues Verfahren verwendet. Multilagen aus Cu- und Ni- Dünnschichten wurden mittels Ionenstrahlbeschichtung (IBS) auf Wolframpfosten beschichtet und durch fokussierte Ionenstrahlung (FIB) geformt. Bei drei unterschiedlichen Temperaturen, zwischen 573 und 673 K, wurden isotherme Auslagerungssequenzen an einem Ultrahochvakuumofen (UHV) durchgeführt und der Mischungsprozess analysiert. Ein Modell des Diffusionsprozesses wurde mittels mathematischer Überlegungen erstellt. Durch das Fitten der experimentellen Kompositionsprofile mittels dieses Modells konnten die Gleichgewichtskonzentrationen der Schichten auch mit relativ kurzen Auslagerungszeiten ermittelt werden. Darüber hinaus konnten aus den diffusionskontrollierten Zeit- und Temperaturdaten physikalische Eigenschaften wie der effektive Diffusionskoeffizient (Gitterdiffusion einschließlich Defektdiffusion) bestimmt werden. Dieser betrug Deff = 1.86 ∙ 10-10 m2/s ∙ exp(-164 kJ mol-1/RT). Während dem Vermischen wurde die Änderung der multilagigen Mikrostruktur bis zur vollständigen Mischung bei 623 und 673 K beobachtet, wobei Korngrenzen als schneller Diffusionsweg eine wichtige Rolle spielen. Bei 573 K wurde Nichtmischbarkeit experimentell deutlich nachgewiesen, wobei die Phasengrenzen bei cNi=26 at.% und cNi=66 at.% liegen. Mit diesen Phasengrenzen wurde die Mischungslücke über eine Redlich-Kister-Parametrisierung der Gibbs‘schen freien Energie über den gesamten Konzentrationsbereich rekonstruiert. Hierin wurde für die kritische Temperatur, TC, 608 K bei einer Konzentration von 45 at% Ni gefunden. Im zweiten Teil wurde die Korngrenzsegregation durch die FIB/tEBSD- (Transmissions-Elektronen-Rückstreubeugung) Technik, in Korrelation zu APT-Messung charakterisiert. Vier Legierungen mit einem Ni-Anteil zwischen 25 und 85 at.% wurden auf Wolframpfosten per IBS beschichtet, und bei 700 K für 24 h wärmebehandelt. Die Segregation von Cu in die Korngrenzen wurde beobachtet. Durch die Verwendung eines theoretischen Models wurde die Exzess-Kurve über den gesamten Konzentrationsbereich, und die Korngrenz-Formationsenergie auf Basis der experimentellen Daten berechnet. Die tEBSD-Analyse während der FIB-Präparation erlaubt die Identifikation der Körner und deren Orientierung. Ein neues Verfahren wurde entwickelt, um mithilfe der Orientierung benachbarter Körner, Berechnungen zur Ermittlung der Korngrenzorientierung durchzuführen und somit die Orientierung natürlicher Korngrenzen zu bestimmen. Mit diesem Verfahren konnte der zeitliche Aufwand dieser anspruchsvollen Auswertung (verglichen zur herkömmlichen Methode mittels TEM-Untersuchung) stark reduziert werden, so dass eine quantitative Analyse vieler Korngrenzen möglich wurde. Aus den einzelnen Korngrenzorientierungen wurde die Korngrenzrotation, und die jeweiligen Anteile an Kippung und Drehung berechnet. Eine Abhängigkeit der Feststoffsegregation vom Kipp- und Drehanteil der Korngrenze wurde beobachtet, die am kleinsten für die reine Kipp- und Drehrotation war. Die ermittelten Segregationsweiten sind signifikant größer als die strukturellen Korngrenzweiten und bewegen sich zwischen 12 und 85 Å. Dieses Verhalten wurde durch eine künstliche Verbreiterung der Korngrenze erklärt, die durch eine Flugbahnabweichung der Korngrenzatome während der Verdampfung verursacht wurde. Eine Korngrenzweite von w0 = (10.1 ± 1.5) Å wurde für eine unverfälschte Korngrenze gefunden.