Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
7 results
Search Results
Item Open Access Polymer electrolyte membrane degradation and mobility in fuel cells : a solid-state NMR investigation(2010) Ghassemzadeh Khoshkroodi, Lida; Müller, Klaus (Prof. Dr.)It is generally believed that fuel cells will play an important role in energy technology already in the near future. Operating polymer electrolyte membrane fuel cells (PEMFCs) at temperatures higher than 100 °C and reduced humidity is anticipated to avoid most of the shortcomings associated with the low-temperature fuel cell operation, such as CO poisoning of the electrode catalysts, slow electrode kinetics of the oxygen reduction reaction and expensive water/thermal management. To date, the operation temperature of PEMFCs is limited to about 90 °C, and this limit is given by the properties of the perfluorosulfonic acid (PFSA) ionomer, Nafion, which is commonly used as a separator material. Apart from the proton conductivity decay at higher temperature and lower humidification, it is also the limited stability of Nafion preventing it from long term operation. Despite the high stability of the PTFE backbone in Nafion, severe deterioration is observed during fuel cell operation. Formation of pinholes and cracks, thinning of the membranes and decrease of ion exchange capacity were reported. The fluorine release indicated that the bond cleavage process takes place under fuel cell operating conditions. Bond cleavage was initially believed to proceed from radical attacks to the carboxyl groups terminating the PTFE backbone of Nafion, and it was claimed to be controlled by the endcapping of the polymer backbone with a CF3 group. However, the release of fluoride was reported even after endcapping of the materials. The observations proved that bond cleavage limits the stability of PFSA membranes, but the elementary reactions and consequences on the membrane microstructure are not fully understood yet. In this work, it has been tried to get new insights into the problems of long term stability of polymer electrolytes for low temperature fuel cells. The aim was to identify the changes in the chemical structure of the membrane after operating in a fuel cell. This understanding is essential for extending the operation limit of PFSA-type membranes by either improving the membrane properties or adjusting the conditions within the running fuel cell. In the present work, therefore the changes taking place in PFSA membranes after applying in-situ and ex-situ aging protocols have been investigated. While the in-situ experiments provide a global picture, the analysis of membranes after ex-situ tests, with various conditions, allows the separation of different types of reactions. In previous studies the degradation changes were mainly monitored by analyzing the released water of the fuel cell or by using the liquid ionomers. In this work with the help of solid-state NMR spectroscopy, the direct study of the chemical structure and dynamics of the polymer membranes before and after the degradation tests became possible. The structural changes in different parts of the PFSA membranes were first inspected after an in-situ aging test. These examined membranes (Nafion and Hyflon Ion) differed by the length of the side chains. The comparison of the solid-state 13C and 19F NMR data of polymers before and after the in-situ degradation test showed that changes can take place not only in the main chain of the polymer, but also within the polymer side chains, as reflected by changes of NMR signals associated with CFSO3, CF3, OCF2 and CF groups. The degree of degradation is found to decrease with increasing membrane thickness while for a given thickness the short side chain polymer, Hyflon Ion, appears to degrade less than Nafion. In order to understand the reason for these observations, a new ex-situ method has been developed to mimic the degradation of polymer electrolyte membranes in PEM fuel cells (caused by the cross-leakage of H2 and O2). In this ex-situ setup, it was possible to expose membranes to flows of different gases with controlled temperature and humidity. H+-form Nafion films with and without electrode layer (Pt) have been treated in the presence of different gases in order to simulate the anode and cathode side of a PEMFC. The changes of the chemical structure occurring during the degradation tests were primarily examined by solid-state 19F NMR spectroscopy. For completion, liquid-state NMR studies and ion exchange capacity measurements were performed. It was found that degradation occurs only when both H2 and O2 are present (condition of gas cross-leakage), and when the membrane is coated with Pt catalyst. The chemical degradation rate is found to be highest for H2-rich mixtures of H2 and O2, which corresponds to the conditions at the anode under OCV. It is further shown that side chain disintegration is very important for chemical degradation, although backbone decomposition also might take place. The fact that in-situ degradation effects were reproduced by the present ex-situ experiments, suggest that membrane degradation in a running fuel cell is mainly the consequence of chemical aging. Detecting the degradation for the membranes coated with Pt in the presence of both gases, H2 and O2, points toward the importance of radicals in the degradation process, which in a running fuel cell (in-situ conditions) may only form in the presence of some gas cross-over, allowing H2 and O2 to react at the Pt catalyst of the anode or cathode structure. Since the gas cross-over increases for the thinner Nafion membrane, these results indirectly explain the higher degradation rate of thin Nafion in the in-situ degradation test. The chemical degradation and stability of PFSA membranes against radical attacks was also investigated in a Fenton ex-situ degradation test. Liquid and solid-state NMR as well as ATR-FTIR spectroscopy were applied to the samples before and after the Fenton reaction. A Comparison of the degradation rate of Nafion and Hyflon Ion in the ex-situ Fenton test again proved that the Hyflon Ion membrane is more stable than Nafion. Comparing the degradation rate of the side chain in these two polymers showed that the stability of Hyflon Ion is mainly due to the shortening of the side chain in this polymer. Hence, the absence of one ether group and the tertiary carbon reduces the degradation rate of the side chain and makes this polymer less sensitive to the radical attacks than Nafion. For the performance of a membrane not only the chemical structure but also the polymer dynamics is important. Therefore the molecular mobility of the ionomer was investigated by variable temperature 19F NMR lineshape, T1 and T1ρ relaxation experiments. The decrease of the temperature dependent linewidth was explained by the reduction of static disorder in the Nafion membrane. From the relaxation data there was evidence for structural annealing, which is independent of the chemical degradation. Chemical degradation is considered to reduce the chain flexibility (i.e. the motional amplitudes), which may be explained by chain cross-linking and condensation reaction for the side chains. To overcome the problem of Nafion's low conductivity at temperatures above 100 °C and low relative humidity, also composite membranes were introduced. These membranes consist of Nafion modified by inorganic oxide additives. It has been reported that under dry conditions, these membranes show enhanced water uptake and water diffusion when compared with filler-free Nafion. In order to understand the reason for the better performance of these polymers, the impact of the oxide particles on the polymer dynamics has been investigated. [Nafion/(SiO2)x] composite membranes in the dry and wet state with x ranging from 0 to 15 w/w% were investigated by variable temperature solid-state 19F NMR spectroscopy. 19F T1 and T1ρ relaxation times and NMR lineshapes were analyzed in order to get details about the polymer mobility. It is concluded that solid oxide SiO2 particles play an important role in stabilizing the chemical structure and morphology of the polymer especially in the dry state. The filler particles lead to higher mobility of polymer chains, if the filler content has an optimized value of about 9 w/w%. The results were further supported by comparing the sideband intensity as well as the linewidth in 19F NMR and recording the 19F{1H} CP/MAS NMR spectra. Furthermore, it has been shown that the structure of composite membranes is more stable after dehydration and possible condensation reactions are less likely in these membranes. The presence of filler particles decrease the chance for morphology changes and close packing of polymer chains in the dry state. Also the decrease of ionic exchange capacity after dehydration is less severe for the composite membrane as compared to filler-free Nafion. In conclusion, the present results provide a complete picture of solid membrane before and after degradation and of possible mechanisms for radical formation and radical attacks to the polymer. In addition, it is shown which changes can occur in the morphology of polymer chains in low humidification and high temperature. Some general suggestions for the better performance of polymer electrolyte membrane are therefore: For improving the performance of polymer electrode membrane, the sources for the radical formation in the fuel cell should be controlled. This can be possible to some extend by avoiding the use of iron end plates in the fuel cells. Also the chance for the gas crossover through the membrane should be decreased. Thicker membranes show less gas cross-over. By taking into account the higher resistivity of thicker membranes, an optimized membrane thickness should be selected. Hydrocarbon sulfonated polyetherketones possess narrower hydrophilic channels which significantly reduce electroosmotic drag, water permeation as well as gas cross-over. Also the short side chain perfluorinated polymer, Hyflon Ion, with lower electroosmotic drag of water should possess a reduced gas cross-over though the membrane. The more efficient way for decreasing degradation is to use membranes which are stable against radical attacks. At this point the perfluorinated polymers are still the best available membranes. Endcapping of the backbone in these polymers and decreasing the concentration of reactive end groups like COOH during the polymer manufacturing process can significantly decrease degradation. To minimize degradation of the side chains in perfluorinated polymers, short side chain polymers are suggested because of less reactive groups for the radical attacks and higher concentration of acidic groups. When higher operation temperatures are required, composite Nafion membranes might be used. The higher stability of these membranes makes them advantageous for operating at evaluated temperatures and low relative humidity. The novel results from the present work lead to a better understanding of membrane degradation, which still represents a serious problem for fuel cells under operation conditions, and provide important indications for future developments of membranes with improved performance for alternative energy conversion devices.Item Open Access Asymmetric Rh diene catalysis under confinement : isoxazole ring‐contraction in mesoporous solids(2024) Marshall, Max; Dilruba, Zarfishan; Beurer, Ann‐Katrin; Bieck, Kira; Emmerling, Sebastian; Markus, Felix; Vogler, Charlotte; Ziegler, Felix; Fuhrer, Marina; Liu, Sherri S. Y.; Kousik, Shravan R.; Frey, Wolfgang; Traa, Yvonne; Bruckner, Johanna R.; Plietker, Bernd; Buchmeiser, Michael R.; Ludwigs, Sabine; Naumann, Stefan; Atanasova, Petia; Lotsch, Bettina V.; Zens, Anna; Laschat, SabineCovalent immobilization of chiral dienes in mesoporous solids for asymmetric heterogeneous catalysis is highly attractive. In order to study confinement effects in bimolecular vs monomolecular reactions, a series of pseudo‐C2‐symmetrical tetrahydropentalenes was synthesized and immobilized via click reaction on different mesoporous solids (silica, carbon, covalent organic frameworks) and compared with homogeneous conditions. Two types of Rh‐catalyzed reactions were studied: (a) bimolecular nucleophilic 1,2‐additions of phenylboroxine to N‐tosylimine and (b) monomolecular isomerization of isoxazole to 2H‐azirne. Polar support materials performed better than non‐polar ones. Under confinement, bimolecular reactions showed decreased yields, whereas yields in monomolecular reactions were only little affected. Regarding enantioselectivity the opposite trend was observed, i. e. effective enantiocontrol for bimolecular reactions but only little control for monomolecular reactions was found.Item Open Access Shape control in wafer-based aperiodic 3D nanostructures(2014) Jeong, Hyeon-Ho; Mark, Andrew G.; Gibbs, John G.; Reindl, Thomas; Waizmann, Ulrike; Weis, Jürgen; Fischer, PeerControlled local fabrication of three-dimensional (3D) nanostructures is important to explore and enhance the function of single nanodevices, but is experimentally challenging. We present a scheme based on e-beam lithography (EBL) written seeds, and glancing angle deposition (GLAD) grown structures to create nanoscale objects with defined shapes but in aperiodic arrangements. By using a continuous sacrificial corral surrounding the features of interest we grow isolated 3D nanostructures that have complex cross-sections and sidewall morphology that are surrounded by zones of clean substrate.Item Open Access Investigating the long-term kinetics of Pd nanoparticles prepared from microemulsions and the Lindlar catalyst for selective hydrogenation of 3-hexyn-1-ol(2024) Tari, Faeze; Hertle, Sebastian; Wang, Hongguang; Fischer, Julian; Aken, Peter A. van; Sottmann, Thomas; Klemm, Elias; Traa, YvonneThe effect of non-saturated corner and edge sites of Pd particles on the long-term selectivity of cis-3-hexen-1-ol in the hydrogenation of 3-hexyn-1-ol was studied in this work. Non-supported Pd agglomerates were synthesized through the microemulsion synthesis route and used at nalkynol/APdratios between 0.08 and 21 mol/m2for the catalytic conversion of 3-hexyn-1-ol for 20 h. The selectivity of the cis-hexenol product increased by reducing the quantity of Pd catalytic sites (increasing the nalkynol/APdratio) without introducing any modifier or doping agent to poison the nonselective sites. Then, Pd aggregates with fused primary particles and, thus, fewer corner and edge sites were produced through thermal sintering of the agglomerates at 473-723 K. By comparing the catalytic performance of the agglomerates and aggregates, it was observed that at a rather similar kinetic behavior (99.99% conversion and 85-89% selectivity to cis-hexenol), the sintered aggregates could stay selective despite a catalytic surface area about seven times larger. This emphasizes the role of low-coordinated edge and corner sites on the final selectivity of the cis product and demonstrates that thermal sintering allows the number of non-selective sites to be reduced without any need for toxic or organic doping agents or modifiers.Item Open Access Celebrating ten years of covalent organic frameworks for solar energy conversion : past, present and future(2024) Rodríguez‐Camargo, Andrés; Endo, Kenichi; Lotsch, Bettina V.Accelerated anthropogenic emission of greenhouse gases due to increasing energy demands has created a negative impact on our planet. Therefore, the replacement of fossil by renewable energy resources has become of paramount interest, both societally and scientifically. It is within this setting that organic photocatalysts have emerged as a new generation of earth‐abundant catalysts for the conversion of solar radiation into chemical energy. In 2014, the first example of a covalent organic framework (COF) photocatalyst for the hydrogen evolution reaction was reported by our group, which has not only marked the beginning of COF photocatalysis for solar fuel production but also helped to accelerate research into “soft photocatalysis” based on porous polymers in general. In the last decade, significant progress has been made toward developing COFs as robust, molecularly precise platforms emulating artificial photosynthesis. This mini‐review commemorates the 10th anniversary of COF photocatalysis and gives a brief historical overview of the milestones in the field since its inception in 2014. We review milestones in the development of COFs for solar fuel production and related photocatalytic transformations, including hydrogen evolution, oxygen evolution, overall water splitting, CO2 reduction, N2 fixation, oxygen reduction, and alcohol oxidation. We discuss lessons learned for the design of structure‐property‐function relationships in COF photocatalysts, and future perspectives and challenges for the field of “soft photocatalysis” are given.Item Open Access Insights into decoupled solar energy conversion and charge storage in a 2D covalent organic framework for solar battery function(2025) Rath, Bibhuti Bhusan; Fuchs, Laura; Stemmler, Friedrich; Rodríguez-Camargo, Andrés; Wang, Yang; Dorfner, Maximilian F. X.; Olbrich, Johann; Slageren, Joris van; Ortmann, Frank; Lotsch, Bettina V.Decoupling solar energy conversion and storage in a single material offers a great advantage for off-grid applications. Herein, we disclose a two-dimensional naphthalenediimide (NDI)-based covalent organic framework (COF) exhibiting remarkable solar battery performance when used as a photoanode. Light-induced radicals are stabilized within the framework for several hours, offering on-demand charge extraction for electrical energy production. Our study reveals mechanistic insights into the long-term charge stabilization using optical spectroscopy and (photo)electrochemical measurements, in conjunction with density functional theory (DFT) simulations. Among several solvents, water provides the best dielectric screening and energetically favorable proton exchange to stabilize photoinduced radicals for more than 48 h without the need for additional metal cations. This study provides fundamental insights into the optoionic charge storage mechanism in NDI-COF, while introducing a highly tunable, nanoporous material platform that surpasses related materials, such as carbon nitrides, metal–organic frameworks (MOFs), or metal oxides, in terms of charge storage capacity. This study opens new perspectives for the design of optoionic charge-storing materials and the direct storage of solar energy to overcome the intermittency of solar irradiation.Item Open Access Raman characterization of dioxygen species as defects in single-crystal ZnO including their pressure dependence(2025) Fischer, Dieter; Bloos, Dominik; Krajewska, Aleksandra; McNally, Graham M.; Zagorac, Dejan; Schön, Johann ChristianThe defects in zinc oxide crystals are of crucial importance for their usability in many applications and are not yet fully understood. Here, we demonstrate that dioxygen species are present as defects in the grown ZnO, resulting in a bending of the atom layers that lie perpendicular to the c-axis. In the Raman spectra, these defects cause the appearance of bands different from the known bands of perfect ZnO crystals allowed by symmetry. These additional Raman bands, which have been frequently reported for ZnO in the past, can thus be fully explained by the presence of dioxygen species, and the widespread assumption of second-order modes for the assignments of these bands is not necessary. Furthermore, the Raman spectrum belonging to perfect zinc oxide in the ideal wurtzite structure is presented, obtained from small domains in ZnO(0001) crystals exposed to pressures up to 2 GPa. The dependence of the O-O stretching modes on the applied pressure proves the presence of dioxygen species in ZnO, which is also confirmed by phonon calculations of structure models with embedded dioxygen species. The surface quality of the ZnO crystals studied is also reflected in the Raman spectra and is included in the analysis.