Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
Search Results
Item Open Access Modeling and simulation of electronic excitation in oxygen-helium discharges and plasma-assisted combustion(2018) Kuntner, Nikolaj; Riedel, Uwe (Prof. Dr. rer. nat.)The present work concerns the generation of electronically excited oxidizers in non-thermal discharges in the context of plasma-assisted hydrogen and methane combustion at atmospheric pressures. These conditions are of practical relevance for the combustion technology. However, as the conversion of electrical power into particular, chosen chemical degrees of freedom is facilitated by low molecular interaction, the atmospheric parameter range is often neglected in the literature. This work provides the design and validation of accurate and efficient computational models for several experiments in this parameter range.Item Open Access Monodisperse highly ordered and polydisperse biobased solid foams(2018) Andrieux, Sébastien; Stubenrauch, Cosima (Prof. Dr.)The aim of this work was the synthesis of monodisperse highly ordered biobased polymer foams and a comparison with their polydisperse counterparts. We used the biobased and biodegradable polymer chitosan, which we cross-linked with genipin. The polymer foams were synthesised via foam templating, i.e. via a liquid foam whose continuous phase contains a polymer and can be solidified. In order to obtain monodisperse highly ordered polymer foams, one first has to generate monodisperse highly ordered liquid foam templates. We did so by using microfluidics, which allows to produce monodisperse liquid foams with bubble sizes from 200 µm to 800 µm and polydispersities below 5%. The monodisperse foams were collected outside of the microfluidic channels and left to self-order under the influence of gravity and confinement. We studied the kinetics of the cross-linking reaction to find the optimal storage conditions during cross-linking. Once cross-linked we freeze-dried the gelled foams to obtain solid chitosan foams. We compared the morphological properties of the solid foams with those of the liquid templates in order to test the efficiency of the developed templating route. We observed how modifying the cross-linking and drying conditions can strongly affect the morphology of the solid foams. The main issue was to maintain the key properties of the liquid foam template throughout the solidification process, namely the bubble size distribution, the structural order and the density. We then compared the synthesised monodisperse polymer foams with their polydisperse counterparts. Although easy foaming methods exist for the generation of polydisperse foams, they do not allow the control over the polydispersity. We thus used microfluidics to generate liquid chitosan foams with tunable polydispersities from below 5% up to 26%. Microfluidics allows to match the average bubble size and density of the polydisperse liquid chitosan foam with those of the monodisperse counterpart. After solidifying the liquid templates we obtained solid foams with controlled polydispersities and studied the in uence of the polydispersity on the mechanical properties. However, we observed that not the polydispersity but the foam density was the main parameter at play. Moreover, the solid chitosan foams had weak mechanical properties with elastic moduli below 100 kPa. To overcome this issue, we incorporated cellulose nanofibres to the original chitosan solution and followed the developed route for foam templating. We had to adapt the microfluidic parameters to account for the viscosity changes brought about by the nanofibres. However, we managed to produce monodisperse liquid foams having the same bubble size, i.e. ~300 µm, but different amounts of cellulose nanofibres. The cellulose content had a strong influence on the solid foam morphology in general and on the pore connectivity in particular.Item Open Access Analytical energy gradients for open-shell local second-order Møller-Plesset perturbation theory and applications to large molecules(2018) Dornbach, Mark; Werner, Hans-Joachim (Prof. Dr.)Item Open Access Calculation of reaction rate constants via instanton theory in the canonical and microcanonical ensemble(2018) Löhle, Andreas; Kästner, Johannes (Prof. Dr.)Item Open Access Monoclinic SrIrO3 : a Dirac semimetal produced by non-symmorphic symmetry and spin-orbit coupling(2018) Takayama, Tomohiro; Yaresko, Alexander N.; Takagi, HidenoriSrIrO3 crystallizes in a monoclinic structure of distorted hexagonal perovskite at ambient pressure. The transport measurements show that the monoclinic SrIrO3 is a low-carrier density semimetal, as in the orthorhombic perovskite polymorph. The electronic structure calculation indicates a semimetallic band structure with Dirac bands at two high-symmetry points of Brillouin zone only when spin-orbit coupling is incorporated, suggesting that the semimetallic state is produced by the strong spin-orbit coupling. We argue that the Dirac bands are protected by the non-symmorphic symmetry of lattice.Item Open Access Hydrogen transport in thin films : Mg-MgH2 and Ti-TiH2 systems(2018) Hadjixenophontos, EfiHydrogen storage has become progressively important due to increasing energy demand. Magne-sium (Mg/MgH2) is one of the most promising elements of hydrogen uptake, however, the slow kinetics and need for high temperatures during dehydrogenation make this material challenging for mobile applications. Meanwhile, Titanium (Ti/TiH2/TiO2) draws attention due to its catalytic effect in hydrogenation of other metals with higher capacities. A comprehensive way to quantitatively char-acterize the kinetics of hydride formation in both systems (Mg and Ti) is shown here. A technique allowing a large range of pressures and temperatures (room temperature to 300 °C and from 0.05 bar up to 100 bar) is developed successfully. Thin films (50-1000 nm), deposited by ion beam sput-tering (PVD), are used because of their smooth surface and defined structure. In order to study hydrogen transport precisely, X-ray diffraction (XRD), electron microscopy (SEM/FIB/TEM) and electric resistance measurements are used. In the case of Mg, while a Pd coating is used as catalyst, the hydride is formed from the surface towards the substrate and transformation in the morpholo-gy is observed. Parabolic law is followed and the diffusion coefficient of hydrogen in MgH2 is ob-tained at room temperature (2.67 · 10-17 cm2/s). Additionally, a model is created to fit the experi-mental change in resistance during hydrogen loading and shows the changes in the behavior of thicker layers. The interface between Pd/Mg is discussed, since Mg5Pd2 and Mg6Pd are formed at high temperatures and are most dominant over dehydrogenation. However, at room temperature, this interface appears to be more stable. The activation energy of hydrogenation is calculated ex-perimentally from an Arrhenius plot to be equal to Ea = 22.6 ± 2.0 kJ/mol and the pre-factor D0 = 3904 cm2/s. Additional attention is given to magnesium hydride as an anode electrode in Li-ion bat-teries. TEM investigations of thin film electrodes demonstrate the complete lithiation of the mate-rial however, with drastic volume changes, leading to bad reversibility. In Ti the thin oxide layer naturally formed on the surface, appears to play a dominant role in the kinetics of hydrogen transport leading to a linear kinetics. A pressure dependency is observed, while an experimental evaluation of the permeation coefficient in the oxide is also discussed. Important information on the hydrogen transport is obtained in both systems, giving an input for further improvements of such hydrides.Item Open Access PFG-NMR studies of ATP diffusion in PEG-DA hydrogels and aqueous solutions of PEG-DA polymers(2018) Majer, Günter; Southan, AlexanderAdenosine triphosphate (ATP) is the major carrier of chemical energy in cells. The diffusion of ATP in hydrogels, which have a structural resemblance to the natural extracellular matrix, is therefore of great importance to understand many biological processes. In continuation of our recent studies of ATP diffusion in poly(ethylene glycol) diacrylate (PEG-DA) hydrogels by pulsed field gradient nuclear magnetic resonance (PFG-NMR), we present precise diffusion measurements of ATP in aqueous solutions of PEG-DA polymers, which are not cross-linked to a three-dimensional network. The dependence of the ATP diffusion on the polymer volume fraction in the hydrogels, φ, was found to be consistent with the predictions of a modified obstruction model or the free volume theory in combination with the sieving behavior of the polymer chains. The present measurements of ATP diffusion in aqueous solutions of the polymers revealed that the diffusion coefficient is determined by φ only, regardless of whether the polymers are cross-linked or not. These results seem to be inconsistent with the free volume model, according to which voids are formed by a statistical redistribution of surrounding molecules, which is expected to occur more frequently in the case of not cross-linked polymers. The present results indicate that ATP diffusion takes place only in the aqueous regions of the systems, with the volume fraction of the polymers, including a solvating water layer, being blocked for the ATP molecules. The solvating water layer increases the effective volume of the polymers by 66%. This modified obstruction model is most appropriate to correctly describe the ATP diffusion in PEG-DA hydrogels.