Browsing by Author "Bonten, Christian"

Now showing 1 - 20 of 29

Open Access
Additive manufacturing of β-tricalcium phosphate components via Fused Deposition of Ceramics (FDC)
(2020) Eßlinger, Steffen; Grebhardt, Axel; Jäger, Jonas; Kern, Frank; Killinger, Andreas; Bonten, Christian; Gadow, Rainer
Das Paper beschreibt die Compoundierung bioaktiver Keramik (Beta-Tricalciumphosphat) in einer organischen Matrix, die anschließende Extrusion zu Filamenten, die für den FDM-3D-Druck geeignet sind, sowie die Formgebund zu Scaffolds mittels additiver Fertigung. Weiterhin werden fertigungsprozessbegleitende Untersuchungen zur Entbinderung und Sinterung durchgeführt.
Open Access
Biobased immiscible polylactic acid (PLA) : poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) blends : impact of rheological and non-isothermal crystallization on the bead foaming behavior
(2024) Brütting, Christian; Dreier, Julia; Bonten, Christian; Ruckdäschel, Holger
Nowadays, bead foams are of great interest due to their high lightweight potential. The processing of such foams strongly depends on the crystallization and rheological behavior of the polymers used. By blending polymers, these properties can be tailored to obtain beaded foams with low density, small cell size and high cell density. As a bio-based polymer, PLA is of great interest due to its renewable carbon source. PLA suffers from its low thermal and rheological properties, which can be compensated by using blends. The correlation between the PLA/PHBV ratio and the rheological as well as the crystallization behavior was investigated. The use of PHBV as a minor phase significantly changes the rheological properties and increases the crystallization behavior of PLA. These findings were applied to the foam extrusion process to obtain low density bead foams. Bead foams with densities below 100 kg/m 3 , mean cell sizes below 50 µm and cell densities of 1 × 10 7 cells/cm 3 were obtained.
Open Access
Calibration of fiber orientation simulations for LFT : a new approach
(2020) Willems, Fabian; Reitinger, Philip; Bonten, Christian
Short fiber reinforced thermoplastics (SFT) are extensively used due to their excellent mechanical properties and low processing costs. Long fiber reinforced thermoplastics (LFT) show an even more interesting property profile and are increasingly used for structural parts. However, their processing by injection molding is not as simple as for SFT, and their anisotropic properties resulting from the fiber microstructure (fiber orientation, length, and concentration) pose a challenge with regard to the engineering design process. To reliably predict the structural mechanical properties of fiber reinforced thermoplastics by means of micromechanical models, it is also necessary to reliable predict the fiber microstructure. Therefore, it is crucial to calibrate the underlying prediction models, such as the fiber orientation model, within the process simulation. In general, these models may be adjusted manually, but this is usually ineffective and time-consuming. To overcome this challenge, a new calibration method was developed to automatically calibrate the fiber orientation model parameters of the injection molding simulation by means of optimization methods. This optimization routine is based on experimentally determined fiber orientation distributions and leads to optimized parameters for the fiber orientation prediction model within a few minutes. To better understand the influence of the model parameters, different versions of the fiber orientation model, as well as process and material influences on the resulting fiber orientation distribution, were investigated. Finally, the developed approach to calibrate the fiber orientation model was compared with a classical approach, a direct optimization of the whole process simulation. Thereby, the new optimization approach shows a calculation time reduced by the factor 15 with comparable error variance.
Open Access
Comparative analysis of the solid conveying of regrind, virgin and powdery polyolefins in single-screw extrusion
(2022) Johann, Kai S.; Reißing, Adrian; Bonten, Christian
The shape and size of processed materials play a crucial role in the solid conveying characteristics of single-screw extruders. Thus, the increasing amount of plastic regrind leads to new challenges in screw extrusion. This work investigates the conveying behavior of three distinctly different material shapes in an axially as well as a helically grooved solid conveying zone. A uniform virgin polypropylene (PP) granule, an irregularly plate-shaped PP regrind and a powdery polyethylene (PE) are processed at screw speeds up to 1350 rpm. Thereby, frictionally engaged conveying in the grooves is visualized for the utilized powder. Similarly, the virgin granule is subject to forced conveying by interlocking in the grooves. The experimentally determined throughput is furthermore compared to analytical calculations which assume a so-called nut-screw conveying. It is found that these calculations perfectly predict the throughput when processing the virgin granule and the powder in a helically grooved barrel. In contrast, the analytical calculation significantly underestimates the throughput for the regrind. This underestimation is expected to be mainly caused by its plate shape and a difference in bulk density. The actual bulk density in the extruder is probably significantly higher due to both orientation and compaction effects compared to the measured bulk density that is used for the analytical calculation. Additionally, the regrind exhibits a fluctuating throughput due to the non-constant bulk density, which results from an irregular regrind shape and a broad size distribution.
Open Access
Compounding, rheology and numerical simulation of highly filled graphite compounds for potential fuel cell applications
(2023) Celik, Alptekin; Willems, Fabian; Tüzün, Mustafa; Marinova, Svetlana; Heyn, Johannes; Fiedler, Markus; Bonten, Christian
Highly filled plastics may offer a suitable solution within the production process for bipolar plates. However, the compounding of conductive additives and the homogeneous mixing of the plastic melt, as well as the accurate prediction of the material behavior, pose a major challenge for polymer engineers. To support the engineering design process of compounding by twin-screw extruders, this present study offers a method to evaluate the achievable mixing quality based on numerical flow simulations. For this purpose, graphite compounds with a filling content of up to 87 wt.-% were successfully produced and characterized rheologically. Based on a particle tracking method, improved element configurations were found for twin-screw compounding. Furthermore, a method to characterize the wall slip ratios of the compounded material system with different filler content is presented, since highly filled material systems often tend to wall slip during processing, which could have a very large influence on accurate prediction. Numerical simulations of the high capillary rheometer were conducted to predict the pressure loss in the capillary. The simulation results show a good agreement and were experimentally validated. In contrast to the expectation, higher filler grades showed only a lower wall slip than compounds with a low graphite content. Despite occurring wall slip effects, the developed flow simulation for the design of slit dies can provide a good prediction for both low and high filling ratios of the graphite compounds.
Open Access
Deformation behavior investigation of auxetic structure made of poly(butylene adipate-co-terephthalate) biopolymers using finite element method
(2023) Schneider, Yanling; Guski, Vinzenz; Schmauder, Siegfried; Kadkhodapour, Javad; Hufert, Jonas; Grebhardt, Axel; Bonten, Christian
Auxetic structures made of biodegradable polymers are favorable for industrial and daily life applications. In this work, poly(butylene adipate-co-terephthalate) (PBAT) is chosen for the study of the deformation behavior of an inverse-honeycomb auxetic structure manufactured using the fused filament fabrication. The study focus is on auxetic behavior. One characteristic of polymer deformation prediction using finite element (FE) simulation is that no sounded FE model exists, due to the significantly different behavior of polymers under loading. The deformation behavior prediction of auxetic structures made of polymers poses more challenges, due to the coupled influences of material and topology on the overall behavior. Our work presents a general process to simulate auxetic structural deformation behavior for various polymers, such as PBAT, PLA (polylactic acid), and their blends. The current report emphasizes the first one. Limited by the state of the art, there is no unified regulation for calculating the Poisson’s ratio n for auxetic structures. Here, three calculation ways of n are presented based on measured data, one of which is found to be suitable to present the auxetic structural behavior. Still, the influence of the auxetic structural topology on the calculated Poisson’s ratio value is also discussed, and a suggestion is presented. The numerically predicted force-displacement curve, Poisson’s ratio evolution, and the deformed auxetic structural status match the testing results very well. Furthermore, FE simulation results can easily illustrate the stress distribution both statistically and local-topology particularized, which is very helpful in analyzing in-depth the auxetic behavior.
Open Access
Deformation behavior of 3D printed auxetic structures of thermoplastic polymers : PLA, PBAT, and blends
(2023) Hufert, Jonas; Grebhardt, Axel; Schneider, Yanling; Bonten, Christian; Schmauder, Siegfried
Auxetic structures have a negative Poisson’s ratio and therefore expand transversely to the direction of loading instead of tapering. This unique behavior is not caused by the materials used, but by the structure, and thus offers completely new functionalities and design possibilities. As a rule, auxetic structures have a very complex geometry, which makes cost-effective production possible only by means of additive manufacturing processes. Due to the high design freedom of the strand deposition method, it makes sense to manufacture auxetic structures using this process. Therefore, in this project, polylactide acid (PLA), polybutylene adipate terephthalate (PBAT), and blends of the two polymers were produced and characterized. Filaments of the two polymers and a blend were extruded, processed into auxetic structures by strand deposition process (SDP), and investigated for their properties, primarily their Poisson’s ratio. The Poisson’s ratio was determined and the influence of the material on it was identified. A specific number of 5 × 5 unit cells has been found to be ideal for investigation. Dual printed specimens showed a similar auxetic behavior as the specimens made of pure PBAT. Likewise, multiple loading and unloading of the structure is possible. Furthermore, in-situ computed tomography revealed the detailed characterization of the initial state, including the warpage of the structures, damage, and traced auxetic behavior in detail.
Open Access
Degradation of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) reinforced with regenerated cellulose fibers
(2024) Seitz, Michael; Rihm, Rainer; Bonten, Christian
PHBV is a promising plastic for replacing conventional petroleum-based plastics in the future. However, the mechanical properties of PHBV are too low for use in high-stress applications and the degradation of the polymer limits possible applications. In this work, the mechanical properties were, therefore, increased using bio-based regenerated cellulose fibers and degradation processes of the PHBV-RCF composites were detected in accelerated aging tests under various environmental conditions. Mechanical, optical, rheological and thermal analysis methods were used for this characterization. The fibers significantly increased the mechanical properties, in particular the impact strength. Different degradation mechanisms were identified. UV radiation caused the test specimens to fade significantly, but no reduction in mechanical properties was observed. After storage in water and in aqueous solutions, the mechanical properties of the compounds were significantly reduced. The reason for this was assumed to be hydrolytic degradation catalyzed by higher temperatures. The hydrolytic degradation of PHBV was mainly caused by erosion from the test specimen surface. By exposing the regenerated cellulose fibers, this effect could now also be visually verified. For the use of regenerated cellulose fiber-reinforced PHBV in more durable applications, the aging mechanisms that occur must be prevented in the future through the use of stabilizers.
Open Access
Direct Joule heating as a means to efficiently and homogeneously heat thermoplastic prepregs
(2020) Wellekötter, Jochen; Bonten, Christian
Although direct Joule heating is a known technique for heating carbon fiber reinforced plastics, it is a yet unexplored heating method for thermoplastic prepregs before back-injection molding. The knowledge obtained from resistance welding, for example, is not directly transferable because of considerably higher heated volumes and more complex shapes. In this study, the governing parameters and process limits are established for this method. The influences of the contacting, the materials used, and the size of the heated part are investigated with respect to the part temperature and heating efficiency. The findings show that the quality of heating is determined by the shape and size of the electrodes. Larger electrodes lead to a more homogeneous temperature distribution. Parts based on woven fabric can be heated more homogeneously because of the existence of intersections between rovings, generating contact between fibers. An increase in part width results in uneven heating behavior.
Open Access
Enhanced processing of regrind as recycling material in single-screw extruders
(2021) Thieleke, Philipp; Bonten, Christian
Regrind processing poses challenges for single-screw extruders due to the irregularly shaped particles. For grooved feed zones, the output is lessened by the reduction of bulk density in comparison to virgin material. Simultaneously, the melt temperature increases, reducing the extruder’s process window. Through experimental investigations on a test stand, a novel feed zone geometry (nominal diameter 35 mm) is developed. It aligns the regrind’s specific throughput with that of virgin material. The regrind processing window is essentially increased. As the solids conveying in the novel feed zone cannot be simulated with existing methods, numerical simulations using the discrete element method are performed. Since plastic deformation occurs in the novel feed zone geometry, a new hysteresis contact model is developed. In addition to spheres, the regrind and virgin particles are modeled as superquadrics to better approximate the irregular shape. The new contact model’s simulation results show excellent agreement with experimental compression tests. The throughput of the extruder simulations is considerably underestimated when using spheres to represent the real particles than when using irregularly shaped superquadrics. Corresponding advantages can be seen especially for virgin material.
Open Access
Evaluation of the zero shear viscosity, the D-Content and processing conditions as foam relevant parameters for autoclave foaming of standard polylactide (PLA)
(2020) Standau, Tobias; Long, Huan; Murillo Castellón, Svenja; Brütting, Christian; Bonten, Christian; Altstädt, Volker
In this comprehensive study, the influence of (i) material specific properties (e.g., molecular weight, zero shear viscosity, D-content) and (ii) process parameters (e.g., saturation temperature, -time, -pressure, and pressure drop rate) on the expansion behavior during the autoclave foaming process were investigated on linear Polylactide (PLA) grades, to identify and evaluate the foam relevant parameters. Its poor rheological behavior is often stated as a drawback of PLA, that limits its foamability. Therefore, nine PLA grades with different melt strength and zero shear viscosity were systematically chosen to identify whether these are the main factors governing the foam expansion and whether there is a critical value for these rheological parameters to be exceeded, to achieve low density foams with fine cells. With pressure drop induced batch foaming experiments, it could be shown that all of the investigated PLA grades could be foamed without the often used chemical modifications, although with different degrees of expansion. Interestingly, PLAs foaming behavior is rather complex and can be influenced by many other factors due to its special nature. A low molecular weight combined with a high ability to crystallize only lead to intermediate density reduction. In contrast, a higher molecular weight (i.e., increased zero shear viscosity) leads to significant increased expandability independent from the D-content. However, the D-content plays a crucial role in terms of foaming temperature and crystallization. Furthermore, the applied process parameters govern foam expansion, cell size and crystallization.
Open Access
Experimental and simulative analysis of the pressure development in a closed injection pultrusion process with multiple chamber geometries
(2023) Strauss, Sebastian; Wilhelm, Frederik; Senz, Andreas; Engelen, Herbert; Boysen, Simon; Rilli, Niko; Celik, Alptekin; Ratka, Marcel; Bonten, Christian
The use of innovative higher-performance highly reactive resin systems requires an enhancement of the established method of fiber impregnation (open bath) towards closed resin-injection pultrusion (CIP), due to the short pot life of the resin systems. The result is that the open bath is developed into a closed injection and impregnation chamber (“ii-chamber”). In this study, three parameters - resin viscosity, opening angle and opening factor at the injection point on the ii-chamber - are varied, each in three stages. For each set of parameters, a pultrusion trial is conducted and the process pressures in the ii-chamber and pultrusion die measured. This enables direct feedback via the process conditions of the as yet uncured composite. The data obtained are used to validate a newly developed simulation model. The model is based on Darcy’s law, which has been extended to take fiber movement into account and thus represent the resulting pressure increase in the die. The flexible ii-chamber and die concept enhance our understanding of the processes taking place in the die system. The sensitivity of the process pressures can be shown for the three influencing variables. The experiment shows that of the three influencing variables investigated, viscosity has the greatest sensitivity to pressure development. In general, it can be said that over the length of the pultrusion die system, the pressure level increases across the three measuring points.
Open Access
Experimental investigation of the solid conveying behavior of smooth and grooved single-screw extruders at high screw speeds
(2022) Johann, Kai S.; Mehlich, Stephan; Laichinger, Marcus; Bonten, Christian
Single-screw extrusion at high screw speeds is established nowadays since it allows for a high mass throughput at a comparatively small extruder size. Compared to conventional extrusion at low screw speeds, a considerable non-linearity in mass throughput appears by exceeding a certain threshold screw speed. In this study, the solid conveying behavior of different plastic granules with varying geometries was investigated in a smooth, a helically and an axially grooved solid conveying zone for screw speeds up to 1350 rpm. These experimental findings are compared to classical analytical predictions in the literature. It is found for the first time that both the shape and size of the plastic granules play a decisive role in determining the threshold screw speed at which a non-linear mass throughput is observed. It is shown that small and spherical granules exhibit a later onset of non-linear throughput compared to larger lenticular and cylindrical shaped granules. Moreover, it is revealed that the mass throughput equalizes for an axially and a helically grooved solid conveying zone at high screw speeds. This is contrary to the low screw speed range where the axially grooved barrel results in a significantly higher throughput than the helically grooved barrel. Thus, the maximum throughput at high screw speeds is limited by the granule stream provided by the hopper opening and is no longer governed by the groove angle.
Open Access
Extrusion-based 3D printing of poly(ethylene glycol) diacrylate hydrogels containing positively and negatively charged groups
(2018) Joas, Sebastian; Tovar, Günter E. M.; Celik, Oguz; Bonten, Christian; Southan, Alexander
Hydrogels are an interesting class of materials used in extrusion-based 3D printing, e.g., for drug delivery or tissue engineering. However, new hydrogel formulations for 3D printing as well as a detailed understanding of crucial formulation properties for 3D printing are needed. In this contribution, hydrogels based on poly(ethylene glycol) diacrylate (PEG-DA) and the charged monomers 3-sulfopropyl acrylate and [2-(acryloyloxy)ethyl]trimethylammonium chloride are formulated for 3D printing, together with Poloxamer 407 (P407). Chemical curing of formulations with PEG-DA and up to 5% (w/w) of the charged monomers was possible without difficulty. Through careful examination of the rheological properties of the non-cured formulations, it was found that flow properties of formulations with a high P407 concentration of 22.5% (w/w) possessed yield stresses well above 100 Pa together with pronounced shear thinning behavior. Thus, those formulations could be processed by 3D printing, as demonstrated by the generation of pyramidal objects. Modelling of the flow profile during 3D printing suggests that a plug-like laminar flow is prevalent inside the printer capillary. Under such circumstances, fast recovery of a high vicosity after material deposition might not be necessary to guarantee shape fidelity because the majority of the 3D printed volume does not face any relevant shear stress during printing.
Open Access
In situ laboratory for plastic degradation in the Red Sea
(2022) Brümmer, Franz; Schnepf, Uwe; Resch, Julia; Jemmali, Raouf; Abdi, Rahma; Kamel, Hesham Mostafa; Bonten, Christian; Müller, Ralph-Walter
Degradation and fragmentation of plastics in the environment are still poorly understood. This is partly caused by the lack of long-term studies and methods that determine weathering duration. We here present a novel study object that preserves information on plastic age: microplastic (MP) resin pellets from the wreck of the SS Hamada, a ship that foundered twenty-nine years ago at the coast of Wadi el Gemal national park, Egypt. Its sinking date enabled us to precisely determine how long MP rested in the wreck and a nearby beach, on which part of the load was washed off. Pellets from both sampling sites were analyzed by microscopy, X-ray tomography, spectroscopy, calorimetry, gel permeation chromatography, and rheology. Most pellets were made of low-density polyethylene, but a minor proportion also consisted of high-density polyethylene. MP from inside the wreck showed no signs of degradation compared to pristine reference samples. Contrary, beached plastics exhibited changes on all structural levels, which sometimes caused fragmentation. These findings provide further evidence that plastic degradation under saltwater conditions is comparatively slow, whereas UV radiation and high temperatures on beaches are major drivers of that process. Future long-term studies should focus on underlying mechanisms and timescales of plastic degradation.
Open Access
Insights into the processing of recycled carbon fibers via injection molding compounding
(2020) Wellekötter, Jochen; Resch, Julia; Baz, Stephan; Gresser, Götz Theo; Bonten, Christian
Although fiber-reinforced plastics combine high strength and stiffness with being lightweight, major difficulties arise with high volume production and the return of manufactured parts back into the cycle of materials at the end of their lifecycles. In a novel approach, structural parts were produced from recycled material while utilizing the so-called injection molding compounding process. Recycled fibers and recycled polyamide matrix material were used by blending carbon and matrix fibers into a sliver before processing. Injection molding was then used to produce long fiber-reinforced parts through a direct fiber feed system. Recycled matrix granules were incorporated into the injection molding process by means of an injection molding compounder to investigate their influences on the mechanical properties of the parts. The findings show that the recycled fibers and matrix perform well in standardized tests, although fiber length and fiber content vary significantly and remain below expectations.
Open Access
Investigation of auxetic structural deformation behavior of PBAT polymers using process and finite element simulation
(2023) Schneider, Yanling; Guski, Vinzenz; Sahin, Ahmet O.; Schmauder, Siegfried; Kadkhodapour, Javad; Hufert, Jonas; Grebhardt, Axel; Bonten, Christian
The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 x 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, was used to produce such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to their layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to its very fine structure. Instead, the finite-element (FE)-based process simulation realized using an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligibly slight deviation compared to the design topology. This process simulation also provides the temperature evolution of a small-volume material, revealing the effects of local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without consideration of the RS, the effect of the RS on the deformation behavior is discussed for the global force-displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and the evolution, where the first three and the warpage are also compared with the experimental results. Furthermore, the FE simulation can easily provide the global stress-strain flow curve with the total stress calculated from the elemental stresses.
Open Access
Investigation of auxetic structural deformation behavior of PBAT polymers using process and finite element simulation
(2023) Schneider, Yanling; Guski, Vinzenz; Sahin, Ahmet O.; Schmauder, Siegfried; Kadkhodapour, Javad; Hufert, Jonas; Grebhardt, Axel; Bonten, Christian
The current work investigates the auxetic tensile deformation behavior of the inversehoneycomb structure with 5 × 5 cells made of biodegradable poly(butylene adipate-coterephthalate) (PBAT). Fused deposition modeling, an additive manufacturing method, was used to produce such specimens. Residual stress (RS) and warpage, more or less, always exist in such specimens due to their layer-by-layer fabrication, i.e., repeated heating and cooling. The RS influences the auxetic deformation behavior, but its measurement is challenging due to its very fine structure. Instead, the finite-element (FE)-based process simulation realized using an ABAQUS plug-in numerically predicts the RS and warpage. The predicted warpage shows a negligibly slight deviation compared to the design topology. This process simulation also provides the temperature evolution of a small-volume material, revealing the effects of local cyclic heating and cooling. The achieved RS serves as the initial condition for the FE model used to investigate the auxetic tensile behavior. With the outcomes from FE calculation without consideration of the RS, the effect of the RS on the deformation behavior is discussed for the global force–displacement curve, the structural Poisson’s ratio evolution, the deformed structural status, the stress distribution, and the evolution, where the first three and the warpage are also compared with the experimental results. Furthermore, the FE simulation can easily provide the global stress–strain flow curve with the total stress calculated from the elemental stresses.
Open Access
Investigation of the thermal and hydrolytic degradation of polylactide during autoclave foaming
(2021) Dreier, Julia; Brütting, Christian; Ruckdäschel, Holger; Altstädt, Volker; Bonten, Christian
Polylactide (PLA) is one of the most important bioplastics worldwide and thus represents a good potential substitute for bead foams made of the fossil-based Polystyrene (PS). However, foaming of PLA comes with a few challenges. One disadvantage of commercially available PLA is its low melt strength and elongation properties, which play an important role in foaming. As a polyester, PLA is also very sensitive to thermal and hydrolytic degradation. Possibilities to overcome these disadvantages can be found in literature, but improving the properties for foaming of PLA as well as the degradation behavior during foaming have not been investigated yet. In this study, reactive extrusion on a twin-screw extruder is used to modify PLA in order to increase the melt strength and to protect it against thermal degradation and hydrolysis. PLA foams are produced in an already known process from the literature and the influence of the modifiers on the properties is estimated. The results show that it is possible to enhance the foaming properties of PLA and to protect it against hydrolysis at the same time.
Open Access
Mechanical properties of 3D-printed liquid crystalline polymers with low and high melting temperatures
(2023) Johann, Kai S.; Wolf, Andreas; Bonten, Christian
Additive manufacturing allows for the production of complex components using various types of materials such as plastics, metals and ceramics without the need for molding tools. In the field of high-performance polymers, semi-crystalline polymers such as polyetheretherketone (PEEK) or amorphous polymers such as polyetherimide (PEI) are already successfully applied. Contrary to semi-crystalline and amorphous polymers, thermotropic liquid crystalline polymers (LCPs) do not change into an isotropic liquid during melting. Instead, they possess anisotropic properties in their liquid phase. Within the scope of this work, this special group of polymers was investigated with regard to its suitability for processing by means of fused filament fabrication. Using an LCP with a low melting temperature of around 280 °C is compared to processing an LCP that exhibits a high melting temperature around 330 °C. In doing so, it was revealed that the achievable mechanical properties strongly depend on the process parameters such as the direction of deposition, printing temperature, printing speed and layer height. At a layer height of 0.10 mm, a Young’s modulus of 27.3 GPa was achieved. Moreover, by employing an annealing step after the printing process, the tensile strength could be increased up to 406 MPa at a layer height of 0.15 mm. Regarding the general suitability for FFF as well as the achieved uniaxial mechanical properties, the LCP with a low melting temperature was advantageous compared to the LCP with a high melting temperature.