Browsing by Author "Ožbolt, Joško"

Now showing 1 - 5 of 5

Open Access
Can a hand-held 3D scanner capture temperature-induced strain of mortar samples : comparison between experimental measurements and numerical simulations
(2023) Haynack, Alexander; Zadran, Sekandar; Timothy, Jithender J.; Gambarelli, Serena; Kränkel, Thomas; Thiel, Charlotte; Ožbolt, Joško; Gehlen, Christoph
The expected lifespan of cement-based materials, particularly concrete, is at least 50 years. Changes in the pore structure of the material need to be considered due to external influences and associated transport processes. The expansion behaviour of concrete and mortar during freeze-thaw attacks, combined with de-icing salt agents, is crucial for both internal and external damage. It is essential to determine and simulate the expansion behaviour of these materials in the laboratory, as well as detect the slow, long-term expansion in real structures. This study measures the expansion of mortar samples during freeze-thaw loading using a high-resolution hand-held 3D laser scanner. The specimens are prepared with fully or partially saturated pore structures through water storage or drying. During freeze-thaw experiments, the specimens are exposed to pure water or a 3% sodium chloride solution (NaCl). Results show contraction during freezing and subsequent expansion during thawing. Both test solutions exhibit similar expansion behaviour, with differences primarily due to saturation levels. Further investigations are required to explore the changing expansion behaviour caused by increasing microcracking resulting from continuous freeze-thaw cycles. A numerical analysis using a 3D coupled hygro-thermo-mechanical (HTM) model is conducted to examine the freeze–thaw behaviour of the mortar. The model accurately represents the freezing deformation during the freeze–thaw cycle.
Open Access
Design recommendations for concrete pryout capacity of headed steel studs and post-installed anchors
(2023) Jebara, Khalil; Sharma, Akanshu; Ožbolt, Joško
Current formulas to assess the shear capacity of headed steel stud anchors and post-installed (PI) anchors in case of pryout failure (sometimes known as pull-rear failure) have been derived either based on the indirect-tension resistance model or are fully empirical based on push-out test results. In both cases, the predicted pryout capacity is clearly conservative and underestimates the true pryout capacity of anchorages, especially for stiff anchors with low embedment-to-diameter ratios (hef/d < 4.5). This paper proposes an empirical and a semi-empirical formula to predict the concrete pryout capacity of headed steel studs and PI anchors. They were derived based on an improved indirect-tension model which accounts for the stud diameter and the stud spacing in a group of anchors. Furthermore, a database of 214 monotonic shear tests from the literature, including own tests (push-off and horizontally shear tests), is reevaluated and compared to the provisions of EN1992-4. The scope of this assessment proposal includes single and group of headed steel studs and PI anchors attached to a stiff steel plate as well as shear connectors in composite structures without metal deck embedded in normal-weight concrete.
Open Access
Impact analysis of thermally pre-damaged reinforced concrete frames
(2020) Ožbolt, Joško; Lacković, Luka; Ruta, Daniela
In the present study, the influence of thermally induced damage of reinforced concrete (RC) frames on their static and dynamic response is experimentally and numerically investigated. In the experimental test, the RC frame is first pre-damaged through fire exposure and then loaded from the side with the impact of a steel pendulum. To verify the recently developed coupled thermo-mechanical model for concrete, transient 3D FE simulation is carried out. The rate and temperature-dependent microplane model is used as a constitutive law for concrete. It is first shown that the simulation is able to realistically replicate the experimental test. Subsequently, the numerical parametric study is performed where the dynamic and static response of RC frame is simulated for both hot and cold states. It is shown that the pre-damage of RC frame through fire exposure significantly reduces the resistance and changes the response. Finally, it is demonstrated that for the impact load the rate sensitive constitutive law of concrete significantly contributes to the response of RC frame.
Open Access
Numerical and experimental investigation of anchor channels subjected to tension load in composite slabs with profiled steel decking
(2022) Bogdanić, Anton; Casucci, Daniele; Ožbolt, Joško
In curtain wall applications, anchor channels are frequently installed near the edge of composite slabs with profiled steel decking. The complex concrete geometry of these floor slabs affects the capacity of all concrete failure modes, but there are currently no guidelines or investigations available on this topic. The main objective of the present research is to investigate how the position of anchor channels and the complex slab geometry influence the tensile capacity of anchor channels. For this purpose, an extensive numerical parametric study was performed using the 3D nonlinear FE code MASA, which is based on the microplane constitutive model. In order to validate the numerical results, an experimental program was carried out for some of the configurations possible in practice. Based on the results, recommendations are given for the reduction in the tensile capacity of anchor channels in composite slabs with profiled steel decking.
Open Access
Numerical and experimental investigation on concrete splitting failure of anchor channels
(2021) Bogdanić, Anton; Casucci, Daniele; Ožbolt, Joško
Concrete splitting failure due to tension load can occur when fastening systems are located close to an edge or corner of a concrete member, especially in thin members. This failure mode has not been extensively investigated for anchor channels. Given the current trend in the construction industry towards more slender concrete members, this failure mode will become more and more relevant. In addition, significantly different design rules in the United States and Europe indicate the need for harmonization between codes. Therefore, an extensive numerical parametric study was carried out to evaluate the influence of member thickness, edge distance, and anchor spacing on the capacity of anchor channels in uncracked and unreinforced concrete members. One of the main findings was that the characteristic edge distance depends on the member thickness and can be larger than 3hef (hef = embedment depth) for thin members. Based on the numerical and experimental test results, modifications of the design recommendations for the splitting failure mode are proposed. Overall, the authors recommend performing the splitting verification separately from the concrete breakout to design anchor channels in thin members more accurately.