14 Externe wissenschaftliche Einrichtungen
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/15
Browse
164 results
Search Results
Item Open Access Elektrische und magnetische Eigenschaften metallreicher Seltenerdmetallhalogenide(2004) Ryazanov, Mikhail; Simon Arndt (Prof. Dr.)Im Rahmen dieser Arbeit wurden metallreiche Seltenerdmetallhalogenide unterschiedlicher Valenzelektronenkonzentration dargestellt und ihre physikalischen Eigenschaften untersucht. Dafür wurde sowohl der Weg des Einbaus von Interstitialwasserstoffatomen in die Kristallstruktur als auch die Möglichkeit der Kationen- bzw. Anionensubstitution beschritten. Es wurden Hydridiodide und ternaere Iodidtelluride von Y, La und Gd synthetisiert und charakterisiert. Magnetische und elektrische Messungen weisen auf eine erhebliche Änderung der physikalischen Eigenschaften in Abhängigkeit vom Wasserstoffgehalt hin. Es wurden verschiedene auffallende Effekte, wie z.B. Kolossal-Magnetwiderstand sowie auch Spinclusterglas-Verhalten, beobachtet.Item Open Access Polymer electrolyte membrane degradation and mobility in fuel cells : a solid-state NMR investigation(2010) Ghassemzadeh Khoshkroodi, Lida; Müller, Klaus (Prof. Dr.)It is generally believed that fuel cells will play an important role in energy technology already in the near future. Operating polymer electrolyte membrane fuel cells (PEMFCs) at temperatures higher than 100 °C and reduced humidity is anticipated to avoid most of the shortcomings associated with the low-temperature fuel cell operation, such as CO poisoning of the electrode catalysts, slow electrode kinetics of the oxygen reduction reaction and expensive water/thermal management. To date, the operation temperature of PEMFCs is limited to about 90 °C, and this limit is given by the properties of the perfluorosulfonic acid (PFSA) ionomer, Nafion, which is commonly used as a separator material. Apart from the proton conductivity decay at higher temperature and lower humidification, it is also the limited stability of Nafion preventing it from long term operation. Despite the high stability of the PTFE backbone in Nafion, severe deterioration is observed during fuel cell operation. Formation of pinholes and cracks, thinning of the membranes and decrease of ion exchange capacity were reported. The fluorine release indicated that the bond cleavage process takes place under fuel cell operating conditions. Bond cleavage was initially believed to proceed from radical attacks to the carboxyl groups terminating the PTFE backbone of Nafion, and it was claimed to be controlled by the endcapping of the polymer backbone with a CF3 group. However, the release of fluoride was reported even after endcapping of the materials. The observations proved that bond cleavage limits the stability of PFSA membranes, but the elementary reactions and consequences on the membrane microstructure are not fully understood yet. In this work, it has been tried to get new insights into the problems of long term stability of polymer electrolytes for low temperature fuel cells. The aim was to identify the changes in the chemical structure of the membrane after operating in a fuel cell. This understanding is essential for extending the operation limit of PFSA-type membranes by either improving the membrane properties or adjusting the conditions within the running fuel cell. In the present work, therefore the changes taking place in PFSA membranes after applying in-situ and ex-situ aging protocols have been investigated. While the in-situ experiments provide a global picture, the analysis of membranes after ex-situ tests, with various conditions, allows the separation of different types of reactions. In previous studies the degradation changes were mainly monitored by analyzing the released water of the fuel cell or by using the liquid ionomers. In this work with the help of solid-state NMR spectroscopy, the direct study of the chemical structure and dynamics of the polymer membranes before and after the degradation tests became possible. The structural changes in different parts of the PFSA membranes were first inspected after an in-situ aging test. These examined membranes (Nafion and Hyflon Ion) differed by the length of the side chains. The comparison of the solid-state 13C and 19F NMR data of polymers before and after the in-situ degradation test showed that changes can take place not only in the main chain of the polymer, but also within the polymer side chains, as reflected by changes of NMR signals associated with CFSO3, CF3, OCF2 and CF groups. The degree of degradation is found to decrease with increasing membrane thickness while for a given thickness the short side chain polymer, Hyflon Ion, appears to degrade less than Nafion. In order to understand the reason for these observations, a new ex-situ method has been developed to mimic the degradation of polymer electrolyte membranes in PEM fuel cells (caused by the cross-leakage of H2 and O2). In this ex-situ setup, it was possible to expose membranes to flows of different gases with controlled temperature and humidity. H+-form Nafion films with and without electrode layer (Pt) have been treated in the presence of different gases in order to simulate the anode and cathode side of a PEMFC. The changes of the chemical structure occurring during the degradation tests were primarily examined by solid-state 19F NMR spectroscopy. For completion, liquid-state NMR studies and ion exchange capacity measurements were performed. It was found that degradation occurs only when both H2 and O2 are present (condition of gas cross-leakage), and when the membrane is coated with Pt catalyst. The chemical degradation rate is found to be highest for H2-rich mixtures of H2 and O2, which corresponds to the conditions at the anode under OCV. It is further shown that side chain disintegration is very important for chemical degradation, although backbone decomposition also might take place. The fact that in-situ degradation effects were reproduced by the present ex-situ experiments, suggest that membrane degradation in a running fuel cell is mainly the consequence of chemical aging. Detecting the degradation for the membranes coated with Pt in the presence of both gases, H2 and O2, points toward the importance of radicals in the degradation process, which in a running fuel cell (in-situ conditions) may only form in the presence of some gas cross-over, allowing H2 and O2 to react at the Pt catalyst of the anode or cathode structure. Since the gas cross-over increases for the thinner Nafion membrane, these results indirectly explain the higher degradation rate of thin Nafion in the in-situ degradation test. The chemical degradation and stability of PFSA membranes against radical attacks was also investigated in a Fenton ex-situ degradation test. Liquid and solid-state NMR as well as ATR-FTIR spectroscopy were applied to the samples before and after the Fenton reaction. A Comparison of the degradation rate of Nafion and Hyflon Ion in the ex-situ Fenton test again proved that the Hyflon Ion membrane is more stable than Nafion. Comparing the degradation rate of the side chain in these two polymers showed that the stability of Hyflon Ion is mainly due to the shortening of the side chain in this polymer. Hence, the absence of one ether group and the tertiary carbon reduces the degradation rate of the side chain and makes this polymer less sensitive to the radical attacks than Nafion. For the performance of a membrane not only the chemical structure but also the polymer dynamics is important. Therefore the molecular mobility of the ionomer was investigated by variable temperature 19F NMR lineshape, T1 and T1ρ relaxation experiments. The decrease of the temperature dependent linewidth was explained by the reduction of static disorder in the Nafion membrane. From the relaxation data there was evidence for structural annealing, which is independent of the chemical degradation. Chemical degradation is considered to reduce the chain flexibility (i.e. the motional amplitudes), which may be explained by chain cross-linking and condensation reaction for the side chains. To overcome the problem of Nafion's low conductivity at temperatures above 100 °C and low relative humidity, also composite membranes were introduced. These membranes consist of Nafion modified by inorganic oxide additives. It has been reported that under dry conditions, these membranes show enhanced water uptake and water diffusion when compared with filler-free Nafion. In order to understand the reason for the better performance of these polymers, the impact of the oxide particles on the polymer dynamics has been investigated. [Nafion/(SiO2)x] composite membranes in the dry and wet state with x ranging from 0 to 15 w/w% were investigated by variable temperature solid-state 19F NMR spectroscopy. 19F T1 and T1ρ relaxation times and NMR lineshapes were analyzed in order to get details about the polymer mobility. It is concluded that solid oxide SiO2 particles play an important role in stabilizing the chemical structure and morphology of the polymer especially in the dry state. The filler particles lead to higher mobility of polymer chains, if the filler content has an optimized value of about 9 w/w%. The results were further supported by comparing the sideband intensity as well as the linewidth in 19F NMR and recording the 19F{1H} CP/MAS NMR spectra. Furthermore, it has been shown that the structure of composite membranes is more stable after dehydration and possible condensation reactions are less likely in these membranes. The presence of filler particles decrease the chance for morphology changes and close packing of polymer chains in the dry state. Also the decrease of ionic exchange capacity after dehydration is less severe for the composite membrane as compared to filler-free Nafion. In conclusion, the present results provide a complete picture of solid membrane before and after degradation and of possible mechanisms for radical formation and radical attacks to the polymer. In addition, it is shown which changes can occur in the morphology of polymer chains in low humidification and high temperature. Some general suggestions for the better performance of polymer electrolyte membrane are therefore: For improving the performance of polymer electrode membrane, the sources for the radical formation in the fuel cell should be controlled. This can be possible to some extend by avoiding the use of iron end plates in the fuel cells. Also the chance for the gas crossover through the membrane should be decreased. Thicker membranes show less gas cross-over. By taking into account the higher resistivity of thicker membranes, an optimized membrane thickness should be selected. Hydrocarbon sulfonated polyetherketones possess narrower hydrophilic channels which significantly reduce electroosmotic drag, water permeation as well as gas cross-over. Also the short side chain perfluorinated polymer, Hyflon Ion, with lower electroosmotic drag of water should possess a reduced gas cross-over though the membrane. The more efficient way for decreasing degradation is to use membranes which are stable against radical attacks. At this point the perfluorinated polymers are still the best available membranes. Endcapping of the backbone in these polymers and decreasing the concentration of reactive end groups like COOH during the polymer manufacturing process can significantly decrease degradation. To minimize degradation of the side chains in perfluorinated polymers, short side chain polymers are suggested because of less reactive groups for the radical attacks and higher concentration of acidic groups. When higher operation temperatures are required, composite Nafion membranes might be used. The higher stability of these membranes makes them advantageous for operating at evaluated temperatures and low relative humidity. The novel results from the present work lead to a better understanding of membrane degradation, which still represents a serious problem for fuel cells under operation conditions, and provide important indications for future developments of membranes with improved performance for alternative energy conversion devices.Item Open Access Ab initio thermodynamic study of defective strontium titanate(2013) Blokhin, Evgeny; Maier, Joachim (Prof. Dr.)In the presented thesis the perfect and defective SrTiO3 bulk crystals and their (001) surfaces are considered on ab initio level. Since the experimental study of the complex defective systems is comparatively expensive and difficult, and the computer performance has been greatly increased in the last years, the ab initio modeling became very efficient tool to be applied in this field. Additionally, there is a significant industrial demand for the investigation and improvements of the performance of the perovskite-based electrochemical devices, e.g. solid oxide fuel cells and permeation membranes. Finally, there is a lack of methodological studies on defect thermodynamics. The oxygen vacancies and iron impurities, as well as their complexes, are the characteristic defects in SrTiO3 perovskite material. The understanding of basic defect properties and defect-induced phenomena under realistic external conditions requires calculation of thermodynamic properties (the free energy and entropy effects). Thus, thesis is focused on atomic vibrations, i.e. phonons, which are necessary to go beyond standard 0°K approximation and to provide a link to the thermodynamic properties at finite temperatures. This is necessary for a realistic treatment of electrochemical devices. The chosen ab initio modeling scheme is found to ensure the most accurate description simultaneously for the structural, electron and phonon properties of the perfect SrTiO3. Namely, the splitting of the phonon frequencies due to the antiferrodistortive phase transition at 105°K is confirmed to be very small (2–12 cm-1). The experimental temperature dependence of the SrTiO3 heat capacity is also successfully reproduced. Further, the modeling scheme is applied for thermodynamic treatment of oxygen vacancies and iron impurities in SrTiO3 at finite temperatures. The calculated phonon densities of states and group-theoretical study of the defect-induced phonon frequencies are used for the experiment analysis. Several defect-induced local phonon modes are identified, and the experimental Raman- and IR-spectroscopy data are interpreted. The Jahn-Teller-type local lattice distortion around both Fe4+ impurity and oxygen vacancy VO is shown to result in Raman- and IR-active phonons. In particular, the experimentally observed Raman frequency near 700 cm-1 is shown to arise for both defects due to a local O ion stretching vibration nearby the Jahn-Teller defect. However, an absence of such a frequency in an experimental phonon spectrum is found to be a manifestation of formation of Fe3+–VO complexes with oxygen vacancies in the first coordination sphere of iron impurities. The Gibbs formation energy calculated for the neutral oxygen vacancies in bulk SrTiO3 taking into account the phonon contribution is found to be in excellent agreement with the experiment. The phonon contribution to the formation energy is shown to increase with temperature, to about 5% above 1000°K. The predicted relative stability of several structural complexes of oxygen vacancy and iron impurity in SrTiO3 is confirmed by known experimental measurements. Several structural models of such Fe3+–VO complexes in SrTiO3 are discriminated according to the XANES and EXAFS experiments. On an example of SrO-terminated SrTiO3 ultrathin films, the one-dimensional confinement effect on the vacancy formation energy is found to be inconsiderable at 0°K. The phonon contribution to the Gibbs free energy of VO formation in such ultrathin films at finite temperatures is shown to be minor. This suggests the further account of anharmonic effects is required. The workflow developed in thesis is proposed for the modeling of wide class of defects in non-metallic solids. Several auxiliary computer tools were designed in order to simplify such possible studies.Item Open Access Ultrafast spectroscopy of single quantum dots(2012) Wolpert, Christian; Lippitz, Markus (Juniorprofessor Dr.)In this thesis, the coherent interaction of single semiconductor quantum dots and ultrafast optical pulses is studied. Under certain conditions, localized exciton transitions in quantum dots can be seen as semi-isolated two-level systems. While this description is sufficient for the explanation of some observations in coherent experiments, it is sometimes necessary to explicitly consider coupling of the discreet quantum states confined to the dot with the environment. We start out from simple, classical examples of coherent spectroscopy and then turn towards experiments where the interaction with the vicinity of the dot becomes an important factor. First, a novel method for transient differential reflectivity spectroscopy of single quantum systems is introduced. It is a pure far-field optical technique which does not require any sophisticated sample preparation steps which makes it applicable to a broad range of structures. Pump pulses excite the sample structure and probe pulses read out the pump-induced changes in the system after a variable delay time. In the case of a single dipole, the signal is given in the form of the spectral inteferogram between the backscattered wave from the particle and the probe light which is reflected at the sample surface. This form of homodyne detection amplifies the weak scattered wave from the particle and thus makes this kind of spectroscopy for single quantum dots feasible. In the remainder of this thesis our spectroscopic method is applied to either characterize the coherent properties of single quantum dots, to prepare and read-out a desired quantum state or to deliberately manipulate them. Coherence times and oscillator strengths are determined for localized exciton transitions. Arbitrary population states can be written by driving coherent population oscillations using resonant pulses, while entangled superpositions of two exciton states in a single dot are investigated by quantum beats on transient differential spectra. We finally exploit the interaction between the dot and a nearby absorbing layer to switch the dot's absorption spectrum on ultrafast timescales via light-induced transient electric fields.Item Open Access Mixed-conducting (Ba,Sr)(Co,Fe,Zn)O3-δ as cathode material for proton-conducting ceramic fuel cells : defect chemistry and oxygen reduction mechanism(2014) Pötzsch, Daniel; Maier, Joachim (Prof. Dr.)In the present study mixed-conducting solid oxides with perovskite structure are investigated regarding their applicability as oxygen electrode (cathode) in solid oxide fuel cells based on proton-conducting electrolyte membranes. This type of high temperature fuel cells is a promising device as it may allow one to decrease the operating temperature. At reduced temperatures the overpotential of the cathode dominants over all contributions to the performance of the fuel cell. Hence, it is mandatory to systematically and purposefully enhance the catalytic activity of the cathode, for which a fundamental understanding of the electrochemical properties of the materials is key. These properties are inter alia determined by the defect chemistry of the material's mobile charge carriers. In humid, oxidizing atmosphere at elevated temperature three defects have to be considered: Oxygen vacancies, interstitial protonic defects associated with a regular oxygen site and electron holes. A mixed proton/hole conductivity in the cathode is highly desired as to make the whole electrode surface catalytically active for water formation. The bulk thermodynamic and transport behavior regarding three mobile charge carriers are significantly more complex than for systems with only'' two mobile defects. Numerical simulations are necessary to describe and understand the bulk thermodynamic and transport properties. The proton concentration of mixed-conducting perovskites was ex-situ determined by Karl-Fischer titration and thermogravimetry analyzing the mass spectrometer signal, and in-situ by dynamic, thermogravimetric relaxation experiments upon step-wise changes in the water partial pressure. BSFZ was found to be the most promising candidate of the four and, therefore, selected for further investigations. From a thermodynamic point of view two limiting possibilities incorporating protons are identified: Incorporating a water molecule occupying an oxygen vacancy and forming two protonic defects (acid-base thermodynamics) and taking up water releasing simultaneously oxygen, i.e. hydration-deoxygenation, formally equivalent to pure hydrogen incorporation (redox thermodynamics). Depending on temperature, oxygen and water partial pressure any combination of both mechanisms is possible. With the help of numerically simulating the transport behavior at different conditions, measuring the mass relaxation upon water partial pressure changes at two different oxygen partial pressures and determining the thermodynamic properties in dry conditions, the proton concentration could be calculated applying the thermodynamic model. For BSFZ the mass relaxation transients upon pH2O change were measured for two different p2O values. Interestingly, the mechanism of proton uptake was found to change from predominantly acid-base water uptake to predominantly redox hydrogen uptake. The transients could be fitted through the known solution of Fick's second law of one-dimensional diffusion into a plane sheet (with sufficiently fast surface equilibration) obtaining chemical diffusivities. The proton conductivity is calculated using its concentration and diffusivity. The obtained values are up to one and a half orders of magnitude below the proton conductivity of 15% Y-doped BaZrO3 being one of the best known high temperature proton conductors. Nevertheless, even the estimate of the lower limit of proton conductivity in BSFZ is orders of magnitude larger than a required minimum to make the whole electrode surface catalytically active. This is to the best of my knowledge the first study providing quantitative values for the proton conductivity in those mixed-conducting perovskites typically used as cathode material in solid oxide fuel cells. The electrochemical activity of BSFZ and BSCF was investigated by impedance spectroscopy. For microelectrodes the low frequency contribution typically dominates the overall impedance, and its resistance is inversely proportional to the reaction rate determining the overall oxygen to water reaction. The inverse dependence of the surface reaction resistance to the area of the microelectrode confirms that the whole electrode surface is catalytically active. Its dependency on oxygen and water partial pressure provides important information about the oxygen reduction mechanism. The exponents of the oxygen and water partial pressure dependency indicate that molecular oxygen and oxygen vacancies are participating in the rate determining step of the oxygen reduction reaction.Item Open Access Organic solar cells : correlation between molecular structure, morphology and device performance(2010) Bruder, Ingmar; Weis, Jürgen (Prof. Dr.)The development of efficient organic solar cells could be one approach to provide mankind with cheap, sustainable and ecofriendly energy. The introduction of bulk heterojunction and tandem device architectures led recently to devices with power conversion efficiencies close or even higher than n = 6%, showing the potential of organic photovoltaics. Nevertheless, to compete for the foreseeable future to inorganic solar cell technologies, the power conversion efficiencies of organic solar cells have to rise further in the range of 10 % into 15 %. Since the functioning of organic photovoltaics is based on a complex interplay of the electronic properties of its molecular components, it is desirable for an efficient evolution, to identify structural and energetical key characteristics of the molecular components that can lead to efficiency gains. Furthermore, there are virtually no limits for the synthesis of new photoactive materials for the use in organic photovoltaics. Therefore, it is crucial for the device fabrication as well as under a chemical point of view, to narrow potentially promissing classes of molecules and their derivatives under certain physical criteria. One aim of this study was to find and identify so far unknown design criteria for molecules providing high efficiencies in organic solar cells. Thus, the question was raised: What is the physical cause for the differing performance of various metal-phthalocyanines (MPc's with M = Zn, Cu, Ni, Fe) in organic solar cells. Therefore, MPc/C60 based bilayer heterojunction solar cells were fabricated showing a clear dependence of the optimal layer thickness and overall performance on the employed MPc material. Initially, the origin of these differences were explored through structural analysises by AFM and high resolution XRPD measurements on powder and evaporated thin films. The optical properties of the metal phthalocyanines were investigated by solidstate fluorescence and absorption measurements. The lowest excited states of the MPc series were explored by correlated multi-reference ab inito calculations. A high open circuit voltage Voc of a solar cell is a prerequisite for high efficiencies. Unfortunately, the Voc of small molecule based organic solar cells is usually considerably lower than the HOMO-LUMO offset of the device, which determines the theoretical maximum of the Voc in a first approximation. Thus, the question was investigated: What causes the difference between the possible open-circuit voltage and the actual measured voltage and how can this difference be reduced? To answer this question, heterojunction solar cells were produced containing ZnPc or one of the novel synthesized Phenyl-ZnPc, Naphtyl-ZnPc or Anthracenyl-ZnPc as p-conducting and C60 as n-conducting organic layers. By adding the respective aryl substituents to the ZnPc core, the polarizability of the molecules was successively increased. Concurrently, an increase of the Voc from 550 mV to 790 mV by using the highly polarizable Anthracenyl-ZnPc instead of ZnPc was achieved. Quantum mechanical calculations, simulating the charge separation mechanism at the DA-interface of Phenyl-ZnPc/C60 and Naphtyl-ZnPc/C60 showed, that the interplay between characteristic packing and polarization effects could lead to considerably different Coulomb interactions of the electron-hole pairs at the DA-interface. The control of the conduction type and Fermi-level of semiconductors is crucial for the realization of all optoelectronic devices. In inorganic as well as in organic devices this can be achieved by defined doping of appropriate areas within the device. Thus, it has been investigated, how the molecular structure of a dopant should be in order to reduce its diffusivity and increase the evaporation temperature to allow a more efficient processing of the compound. As a result, the novel p-dopant 2,3-di(N-phthalimido)-5,6-dicyano-1,4-benzoquinone (BAPD) was synthesized and compared to the state-of-the-art dopant F4TCNQ. In addition to basic and applied physical questions, I worked on the development of new, efficient solar cell architectures during my PhD thesis. In the course of this work it could be shown, that an efficient organic tandem cell can be prepared from a solid state dye-sensitized solar cell combined with a vacuum-deposited bulk heterojunction solar cell. The complementary absorption of the dyes, as well as an adequate serial connection of both subcells, leads to a high power conversion efficiency of n = (6.0±0.1)% under simulated 100 mW/cm2 AM 1.5 illumination.Item Open Access Charge carrier formation, mobility and microstructure of sulfonated polyelectrolytes for electrochemical applications(2015) Wohlfarth, Andreas; Maier, Joachim (Prof. Dr.)Polyelectrolytes are materials consisting of a polymer backbone with covalently attached positively or negatively charge groups including their counterions. Sulfonated polyelectrolytes are a specific class, which is especially interesting for electrochemical application as they can be used to separate the electrodes and mediate the electrochemical reactions taking place at anode and cathode by conducting a specific ion; this ion may be H+ in the case of PEM-fuel cells or Li+ and Na+ in various battery systems. The key challenges for the development of these electrolytes is the combination of good mechanical properties and high ion transport as well as high electrochemical stability. High ionic conductivity of polyelectrolytes depends on the presence of small polar solvents to ensure efficient dissociation and mobility of the counterions. These processes cannot be understood by merely considering electrostatics (i.e. Deby-Hückel approach) such as in Manning counterion condensation theory. Specific interactions between solvent-ion-polymer and the molecular conformations have to be taken into account as well. This is one of the results of the present work using sulfonated polyelectrolytes, different cations and solvents as model systems with a combined approach of experimental techniques and simulations. The dissociation behavior of sulfonated polysulfones was investigated by a combined electrophoretic (E) NMR, pulsed magnetic field gradient (PFG) NMR and conductivity approach. Since the results from the NMR experiments, especially from E-NMR which is by far no standard measurement, are crucial for the key conclusions drawn in this thesis, some critical issues of this technique are studied and discussed in detail. E-NMR is essentially a PFG-NMR experiment with an applied electric field; the applied voltage can reach up to 300 V. Therefore, it was necessary to determine a measurement window in which no decomposition or other interfering effects appeared. In addition, polymers gererally exhibit some polydispersity with the low molecular weight fraction showing a higher diffusion coefficients and drift velocities, which had to be taken into account. By concentrating ionic groups on the polymer, specific polyelectrolyte effects show up. Dissociation is no longer complete, the interaction between ionic charges and the solvent is heavily modified and correlations of ionic motion start to appear. According to a MD-simulation, this very much depends on the polymer conformation and position of the ionic groups as well as the chemical nature of the solvent. Once the density of ionic groups (-SO3H) of polysulfones reaches a point where their average separation is of the order of the Bjerrum length of water, the degree of counterion condensation is shown to depend on details of the molecular structure and the accessible conformations of the polymer chain. In this regime, well-defined ionic aggregates occur, i.e. triple-ions form. The conformational details depend on the degrees of freedom and specific interactions between ions and solvent. When it comes to ion conducting membranes, increasing the ion exchange capacity (decreasing the average separation of ionic groups) is a common measure to increase ionic conductivity. However, the results on dissociation and conductivity of synthesized polysulfones containing octasulfonated units (currently the material with highest known IEC) clearly reveal the limit of this approach. The short separation of ionic charges in such systems at high concentrations additionally leads to electrostatic interactions between neighboring polymer strands. This is the driving force for a nanoscale ordering in polyelectrolyte membranes. Different kinds of solvents, ions and ion exchange capacities directly affect the microstructure formation. Finally, the effects of acid-base interactions between sulfonic acid-based polyelectrolytes and weakly basic modified polymers were investigated as blending of both is a way to form stable membranes for electrochemical applications. Here, the membrane formation process and the resulting properties, in particular proton conductivity, microstructure and mechanical strength have been studied. The developed polymer blends are the first example in which an improvement of mechanical properties not goes along with a significant decrease of proton conductivity. Key to success was to use a hydrophilic polymer with a high IEC and a hydrophobic polymer with a low number of basic groups. In summary, this thesis provides insides into the charge carrier formation process, the transport and microstructure of sulfonated polyelectrolytes by identifying the relevant molecular interactions. Together with the superior mechanical properties of the developed blend membranes, this work significantly contributes to solve the key challenges for electrolytes in electrochemical application.Item Open Access Spectroscopic study of CaMnO3/CaRuO3 superlattices and YTiO3 single crystals(2009) Yordanov, Petar; Keimer, Bernhard (Prof. Dr.)The first two sections of Chapter 1 give a general overview of the research topics and experimental methods discussed in the thesis. Further on, in Chapter 2, some of the most important characteristics and mechanisms underlying the physics of transition metal oxides are presented. As the experimental part of the thesis includes studies on manganites and titanates, these two classes of compounds are exemplified in the exposition of Chapter 2. Several recent works in the emerging research field of transition metal oxide interfaces and superlattices are also discussed along with a brief introduction in x-ray spectroscopic methods with synchrotron radiation. Chapter 3 introduces the principles of optical spectroscopy and the simplest models for dielectric function, i.e., Lorentz oscillator and Drude dielectric function. The following Chapter 4 introduces two of the experimental techniques in optical spectroscopy, reflectance and spectroscopic ellipsometry. Further on, we describe the design of a new home-built apparatus for near-normal reflectance with high magnetic fields. Several critical technical details and findings during the assembling process are also discussed. Chapter 5 represents a comprehensive experimental spectroscopic study of a prototypical superlattice system made from an antiferromagnetic insulator CaMnO3 and a paramagnetic metal CaRuO3. The resulting interface ferromagnetic state was closely investigated by means of optical spectroscopy as well as by soft x-ray scattering and absorption methods. This study led us to the conclusion that magnetic bound states, i.e. magnetic polarons, have to be considered in the description of this SL system. Chapter 6 describes a polarized far infrared reflectance study with high magnetic field on the ferromagnetic Mott insulator YTiO3, single crystals. All 25 infrared-active phonon modes were observed. The temperature and magnetic-field dependence of the phonon modes revealed a weak spin-phonon coupling in YTiO3 and largely extended temperature range (up to TM ~ 80 - 100K), for the field-induced effects on the oscillator parameters. This later observation, uncovered short-range magnetic order state which remains even at temperatures as high as three times the temperature of the actual ferromagnetic transition of Tc ~ 30K. While a quantitative theoretical description of these data is thus far not available, they point to a complex interplay between spin, orbital, and lattice degrees of freedom due to the near-degeneracy of the Ti t2g orbitals in YTiO3.Item Open Access Unconventional properties of non-centrosymmetric superconductors(2010) Klam, Ludwig; Metzner, Walter (Prof. Dr.)A kinetic theory for non-centrosymmetric superconductors (NCS) is formulated for low temperatures and in the clean limit. The transport equations are solved quite generally for any kind of antisymmetric spin-orbit coupling (ASOC) in an extended momentum and frequency range. The result is a particle-hole symmetric, gauge-invariant and charge conserving description, which is used to calculate the current response, the specific heat capacity, and the Raman response function. A detailed analysis of the gauge invariance and the associated phase fluctuations of the superconducting order parameter revealed two gauge modes: the Anderson-Bogoliubov mode on the one side and a new gauge mode on the other side, which strongly depends on the symmetry of the ASOC. As application of the kinetic theory, the polarization-dependence of the T=0 electronic Raman response in NCS is studied for two important classes of ASOC with the representative systems CePt3Si and Li2PdxPt3-xB. Analytical expressions for the Raman vertices are derived, and the frequency power laws and pair-breaking peaks are calculated. A characteristic two-peak structure is predicted for NCS and might serve as an indicator for the unknown relative magnitude of the singlet and triplet contributions to the superconducting order parameter. An efficient numerical method is introduced in order to calculate the dynamical spin and charge response of CePt3Si, using an itinerant description for the electrons. With a realistic parameterization of the band structure, the nesting function, inelastic neutron scattering cross sections, and Kohn anomalies are calculated for a selected band in the normal non-magnetic state. From the spin and charge susceptibility, a superconducting pairing interaction is constructed for the weak-coupling gap equation. A sign analysis of the decoupled gap equation supports the experimental evidence of a strong triplet contribution to the order parameter in CePt3Si. In particular for this compound, it can be shown that an increasing Rashba-type of spin-orbit coupling strengthens the triplet contribution.Item Open Access Synthesis of new fullerides via the "break-and-seal" approach and their characterization(2009) Kozhemyakina, Nina V.; Jansen, Martin (Prof. Dr.)The present dissertation deals with the synthesis and characterization of fullerides. For the first time the "break-and-seal" technique was applied for fulleride synthesis. The reaction was performed in a completely all-glass apparatus under vacuum, avoiding the use of glass connections and use of grease. Starting from crown-ethers, potassium metal and C60 fullerene, six new fullerides have been synthesized. The modified "temperature difference method" was successfully used for growing single crystals from solution within a few days. In [K(DB24C8)(DME)]2C60*(DME) the fullerene unit has a charge of 2-. The (C60)2- units are arranged in hexagonal layers parallel to the ab plane, forming distorted trigonal prisms. The fullerene anions and potassium cations develop a pseudobinary topology which is reminiscent of the CdI2 structure type. Bond lengths' distribution in (C60)2- was examined. One orientation of the dianion was found to match perfectly the one predicted by calculations. KC60(THF)5*(THF)2 crystallizes in a structure with fully ordered C60 units. C60- anion-radicals and K+ form ion pairs. The ion pairs form corrugated layers in the ac crystallographic plane, the given compound being an example for a low-dimensional fulleride partial structure. For the compound [K(DB24C8)(THF)]2C60*THF the structure solution was complicated by the disorder of crown-ether and solvent molecules which could not be overcome, although the (C60)2- unit was ordered. In [K(DB24C8)(DME)]C60 the fullerene unit exists as a monomeric anion-radical and in [K(DB24C8)(DME)]2[C60]2 - as a dimer-dianion. The latter compound is an example of rather not many fulleride structures, where C60 exists in the form of dimers. The interfullerene C-C bond length is 1.57(3) Å. In [4{K(DB18C6)(C60-)}(THF)6]*[C60]*(THF)6 at temperatures above 220 K each of the four C60- units exists in form of anion-radicals, and at lower temperatures - as a dimer-dianion, the interfullerene bond being 1.63(0) Å. The dimers are fully ordered. In addition, uncharged disordered C60 molecules are found, what follows from the charge balance. The low-temperature phase is a first example of a fulleride structure where fullerene exists in three different bonding states: anion-radical monomer, dianion-dimer, and a neutral C60. In the dimer, the pentagons adjacent to sp3-hybridized carbon atoms, are in trans-conformation. DFT calculations were performed, and it is now for the first time that a localization of the negative charge on a small fragment of the C60 cage was found out. Knowing this, it becomes conclusive, considering the Coulombic repulsion, that the preferred orientation of two bound C60- units is trans-conformation. Magnetic measurements were performed. The method for fulleride synthesis used in the present work has a big potential for broadening by using different metals (e.g. alkali, alkali-earth), varying the complexing agents (crown-ethers, cryptands), as well as the organic solvent (or solvent mixtures).