05 Fakultät Informatik, Elektrotechnik und Informationstechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/6
Browse
Item Open Access Coordination chemistry as a universal strategy for a controlled perovskite crystallization(2023) Zuo, Weiwei; Byranvand, Mahdi Malekshahi; Kodalle, Tim; Zohdi, Mohammadreza; Lim, Jaekeun; Carlsen, Brian; Magorian Friedlmeier, Theresa; Kot, Małgorzata; Das, Chittaranjan; Flege, Jan Ingo; Zong, Wansheng; Abate, Antonio; Sutter‐Fella, Carolin M.; Li, Meng; Saliba, MichaelThe most efficient and stable perovskite solar cells (PSCs) are made from a complex mixture of precursors. Typically, to then form a thin film, an extreme oversaturation of the perovskite precursor is initiated to trigger nucleation sites, e.g., by vacuum, an airstream, or a so-called antisolvent. Unfortunately, most oversaturation triggers do not expel the lingering (and highly coordinating) dimethyl sulfoxide (DMSO), which is used as a precursor solvent, from the thin films; this detrimentally affects long-term stability. In this work, (the green) dimethyl sulfide (DMS) is introduced as a novel nucleation trigger for perovskite films combining, uniquely, high coordination and high vapor pressure. This gives DMS a universal scope: DMS replaces other solvents by coordinating more strongly and removes itself once the film formation is finished. To demonstrate this novel coordination chemistry approach, MAPbI3 PSCs are processed, typically dissolved in hard-to-remove (and green) DMSO achieving 21.6% efficiency, among the highest reported efficiencies for this system. To confirm the universality of the strategy, DMS is tested for FAPbI3 as another composition, which shows higher efficiency of 23.5% compared to 20.9% for a device fabricated with chlorobenzene. This work provides a universal strategy to control perovskite crystallization using coordination chemistry, heralding the revival of perovskite compositions with pure DMSO.Item Open Access High‐stable lead‐free solar cells achieved by surface reconstruction of quasi‐2D tin‐based perovskites(2023) Yang, Feng; Zhu, Rui; Zhang, Zuhong; Su, Zhenhuang; Zuo, Weiwei; He, Bingchen; Aldamasy, Mahmoud Hussein; Jia, Yu; Li, Guixiang; Gao, Xingyu; Li, Zhe; Saliba, Michael; Abate, Antonio; Li, MengTin halide perovskites are an appealing alternative to lead perovskites. However, owing to the lower redox potential of Sn(II)/Sn(IV), particularly under the presence of oxygen and water, the accumulation of Sn(IV) at the surface layer will negatively impact the device's performance and stability. To this end, this work has introduced a novel multifunctional molecule, 1,4‐phenyldimethylammonium dibromide diamine (phDMADBr), to form a protective layer on the surface of Sn‐based perovskite films. Strong interactions between phDMADBr and the perovskite surface improve electron transfer, passivating uncoordinated Sn(II), and fortify against water and oxygen. In situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) analysis confirms the enhanced thermal stability of the quasi‐2D phase, and hence the overall enhanced stability of the perovskite. Long‐term stability in devices is achieved, retaining over 90% of the original efficiency for more than 200 hours in a 10% RH moisture N2 environment. These findings propose a new approach to enhance the operational stability of Sn‐based perovskite devices, offering a strategy in advancing lead‐free optoelectronic applications.Item Open Access Ionic liquid Stabilizing high‐efficiency tin halide perovskite solar cells(2021) Li, Guixiang; Su, Zhenhuang; Li, Meng; Yang, Feng; Aldamasy, Mahmoud H.; Pascual, Jorge; Yang, Fengjiu; Liu, Hairui; Zuo, Weiwei; Di Girolamo, Diego; Iqbal, Zafar; Nasti, Giuseppe; Dallmann, André; Gao, Xingyu; Wang, Zhaokui; Saliba, Michael; Abate, AntonioTin halide perovskites attract incremental attention to deliver lead‐free perovskite solar cells. Nevertheless, disordered crystal growth and low defect formation energy, related to Sn(II) oxidation to Sn(IV), limit the efficiency and stability of solar cells. Engineering the processing from perovskite precursor solution preparation to film crystallization is crucial to tackle these issues and enable the full photovoltaic potential of tin halide perovskites. Herein, the ionic liquid n‐butylammonium acetate (BAAc) is used to tune the tin coordination with specific O…Sn chelating bonds and NH…X hydrogen bonds. The coordination between BAAc and tin enables modulation of the crystallization of the perovskite in a thin film. The resulting BAAc‐containing perovskite films are more compact and have a preferential crystal orientation. Moreover, a lower amount of Sn(IV) and related chemical defects are found for the BAAc‐containing perovskites. Tin halide perovskite solar cells processed with BAAc show a power conversion efficiency of over 10%. This value is retained after storing the devices for over 1000 h in nitrogen. This work paves the way toward a more controlled tin‐based perovskite crystallization for stable and efficient lead‐free perovskite photovoltaics.