06 Fakultät Luft- und Raumfahrttechnik und Geodäsie
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/7
Browse
4 results
Search Results
Item Open Access Analysis of collision avoidance manoeuvres using aerodynamic drag for the Flying Laptop satellite(2023) Turco, Fabrizio; Traub, Constantin; Gaißer, Steffen; Burgdorf, Jonas; Klinkner, Sabine; Fasoulas, StefanosCollision avoidance is a topic of growing importance for any satellite orbiting Earth. Especially those satellites without thrusting capabilities face the problem of not being able to perform impulsive collision avoidance manoeuvres. For satellites in low Earth orbits, though, perturbing accelerations due to aerodynamic drag may be used to influence their trajectories, thus offering a possibility to avoid collisions without consuming propellant. Here, this manoeuvring option is investigated for the satellite Flying Laptop of the University of Stuttgart, which orbits the Earth at approximately 600km. In a first step, the satellite is aerodynamically analysed making use of the tool ADBSat. By employing an analytic equation from the literature, in-track separation distances can then be derived following a variation of the ballistic coefficient through a change in attitude. A further examination of the achievable separation distances proves the feasibility of aerodynamic collision avoidance manoeuvres for the Flying Laptop for moderate and high solar and geomagnetic activity. The predicted separation distances are further compared to flight data, where the principle effect of the manoeuvre on the satellite trajectory becomes visible. The results suggest an applicability of collision avoidance manoeuvres for all satellites in comparable and especially in lower orbits than the Flying Laptop , which are able to vary their ballistic coefficient.Item Open Access Novel heat flux controlled surface cooling for hypersonic flight(2023) Hufgard, Fabian; Duernhofer, Christian; Fasoulas, Stefanos; Loehle, StefanThis paper presents a new method in theory and experiment to adjust the transpiration cooling based on the actual measured heat flux. This is particularly useful in extreme heating environments, e.g. atmospheric entry flight or combustion chamber applications. In such environments, usually cooling is set constant based on the vehicle design, yet a mass efficient and performant cooling is sought after. We present a method with real-time surface heat flux determination of the transpiration cooled wall and an automatic adjustment of the cooling. The heat flux is determined based on a system identification process. The heat flux measurement itself is derived non-intrusively from the measurement of pressure inside the plenum, i.e. the region between mass flow controller and porous wall. The particular advantage of this system is that the heat shield material is not weakened by any sensor system and its performance is optimized with respect to cooling needed at a certain heating level. Another new feature of the pressure heat flux transformation is the attenuation of a destabilizing positive feedback loop, where the transpiration cooling controller’s output (i.e. mass flow rate) strongly influences its input (i.e. plenum pressure). We describe the identification of the model parameters for the heat flux determination, which are found and verified by a calibration approach. The controlled cooling was demonstrated in a hot air plasma flow with a reference heat flux of up to 1.4 MW/m 2. The results show the performance and verify the applicability in a real flight environment.Item Open Access Fargo : validation of space-relevant ferrofluid applications on the ISS(2024) Sütterlin, Saskia; Bölke, Daniel; Ehresmann, Manfred; Heinz, Nicolas; Dietrich, Janoah; Karahan, Bahar; Kob, Maximilian; O’Donohue, Michael; Korn, Christian; Grossmann, Steffen; Philipp, Daniel; Steinert, Michael; Acker, Denis; Remane, Yolantha; Kreul, Phil; Schneider, Maximilan; Zajonz, Sebastian; Wank, Bianca; Turco, Fabrizio; Buchfink, Manuel; Gutierrez, Elizabeth; Hofmann, Sonja; Ruffner, Silas; Wagner, Alexander; Breitenbücher, Laura; Schäfer, Felix; Herdrich, Georg; Fasoulas, StefanosThe Ferrofluid Application Research Goes Orbital (FARGO) project desires to harness the potential of ferrofluids for advanced space system applications. Thereby, the student-led research project aims to develop, evaluate and subsequently validate three different ferrofluid-based applications on board the International Space Station (ISS): a novel attitude control system called Ferrowheel as well as a Thermal and an Electrical Switch. The project is part of the Überflieger2 competition of the German Aerospace Center (DLR) in cooperation with the Luxembourg Space Agency (LSA). Central to this study is the role of ferrofluids in ensuring the functional principles to minimize the number of moving components ultimately. Therefore, the proposed systems have the potential to mitigate wear, reduce friction, and consequently improve the longevity and reliability of space systems. In the Ferrowheel, a disc is supported on ferrofluid cushions instead of conventional ball-bearing-mounted rotors. This innovative approach, facilitated by the magnetic pressure positioning of the ferrofluid, eliminates the need for solid-to-solid contact. Circularly arranged coils function as the stator, propelling the disc with a 3-phase control, resulting in a spinning magnetic field. In addition to determining the generated torque, the objective is to validate experiments on system operations in which various acceleration and deceleration manoeuvres, as well as the stored angular momentum, are evaluated. The Electrical Switch leverages a self-manufactured magnetorheological fluid (MRF) developed by augmenting a liquid-metal base with iron powder. As a result, the fluid, akin to ferrofluid, has a magnetic field-responsive movement. Since a liquid metal is used as the base, the ferrofluid-like fluid acts as both the magnetically actuatable and the current conducting fluid. To enable a current flow, the fluid is brought between the two electrical contacts utilizing electropermanent magnets (EPMs). These magnets combine the high magnetic field strengths of permanent magnets with the adaptive switching capability of electromagnets. Compared to all other demand-controlled magnetic field sources, this results in the great advantage that no energy is consumed as long as they are in one state. Only the switching process of the EPMs itself requires a high amount of energy, but only for a relatively short period. The switching behaviour under different loads will be investigated, evaluated, and compared to reference data recorded on Earth. The design of the Thermal Switch is characterized by the fact that it can be actively switched. Active thermal switching is still a relatively new field, so there is little comparative data from industrial solutions. Particularly for spacecraft, thermal design is crucial because the harsh environment of space must be taken into account. In addition to the challenge that heat can only be transferred to the environment via thermal radiation, severe conditions in space are characterized by extreme temperature differences. While extreme heat develops on the satellite surface on the side facing the sun, the opposite is valid on the shaded side. The resulting heat flow, which is irregular in time, location, and direction, leads to temperature peaks and gradients that can affect the system’s performance, functionality, and reliability. Active switching provides selective control over heat transfer, allowing more flexible temperature regulation in critical areas and implementing a dynamic system response. Different design ideas are tested and evaluated for the applications in various experiments. The most suitable design is finally selected, further modified, and tailored for experimentation on the ISS and presented in this study. The most significant challenge is the time-critical factor of only a 1-year development phase. A total of 21 students from six different courses of study and two supervising PhD students from the Institute of Space Systems are involved in the FARGO project, all members of the small satellite student society at the University of Stuttgart, KSat e.V.Item Open Access Chemical heat derived from rocket-borne WADIS-2 experiment(2024) Grygalashvyly, Mykhaylo; Strelnikov, Boris; Strelnikova, Irina; Rapp, Markus; Lübken, Franz-Josef; Schütt, Corinna; Stephan, Claudia; Eberhart, Martin; Löhle, Stefan; Fasoulas, StefanosChemical heating rates were derived from three of the most significant reactions based on the analysis of common volume rocket-borne measurements of temperature, atomic oxygen densities, and neutral air densities. This is one of the first instances of the retrieval of nighttime chemical heat through the utilization of non-emissive observations of atomic oxygen concentrations, obtained through in situ measurements, performed at the Andøya Space Center (69°N, 16°E) at 01:44:00 UTC on 5 March 2015. Furthermore, we determine the heating efficiency for one of the most significant reactions of atomic hydrogen with ozone and illustrate the methodology for such calculations based on known atomic oxygen and temperature. Subsequently, using ozone values obtained from satellite observations, we retrieved odd-hydrogens and total chemical heat. Finally, we compared the retrieved chemical heat with the heat from turbulent energy dissipation. Our findings reveal that the vertically averaged chemical heat is greater than the heat from turbulent energy dissipation throughout the entire mesopause region during nocturnal conditions. The heating rates of turbulent energy dissipation may exceed the chemical heating rates only in narrow peaks, several hundred meters wide.