07 Fakultät Konstruktions-, Produktions- und Fahrzeugtechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/8
Browse
13 results
Search Results
Item Open Access Die Kornstruktur und der Heißrisswiderstand von Laserstrahlschweißnähten in Aluminiumlegierungen(München : utzverlag, 2020) Hagenlocher, Christian; Graf, Thomas (Prof. Dr. phil. nat.)Die Kornstruktur einer Schweißnaht beeinflusst ihren Widerstand gegen die Bildung von Nahtmittenheißrissen. Im Rahmen dieser Arbeit wurde der übergreifende Zusammenhang zwischen Schweißparameter, Kornstruktur und Heißrisswiderstand beim Laserstrahlschweißen durch analytische Gleichungen beschrieben und das resultierende Modell experimentell validiert.Item Open Access Local laser heat treatment of AlSi10Mg as-built parts produced by Laser Powder Bed Fusion(2024) Kramer, Steffen; Jarwitz, Michael; Schulze, Volker; Zanger, FrederikToday, complex structural components for lightweight applications are frequently manufactured by laser powder bed fusion (PBF-LB), often using aluminum alloys such as AlSi10Mg. However, the application of cyclic load cases can be challenging as PBF-LB produced AlSi10Mg parts typically have low ductility and corresponding brittle failure behavior in the as-built condition. Therefore, this paper presents investigations on the feasibility of a laser heat treatment of PBF-LB produced AlSi10Mg parts to locally increase the ductility and decrease the hardness in critical areas. Potential heat treatment process parameters were derived theoretically based on the temperature fields in the material calculated assuming three-dimensional heat conduction and a moving heat source. PBF-LB produced specimens were then laser heat treated at varying laser power and scan speed. Hardness measurements on metallographic cross sections showed hardness reductions of over 35 % without inducing hydrogen pore growth.Item Open Access Tuning the hardness of produced parts by adjusting the cooling rate during laser-based powder bed fusion of AlSi10Mg by adapting the process parameters(2022) Leis, Artur; Traunecker, David; Weber, Rudolf; Graf, ThomasThe mechanical properties of parts produced by laser-based powder bed fusion (LPBF) are mainly determined by the grain structure in the material, which is governed by the cooling rate during solidification. This cooling rate strongly depends on the scan velocity and the absorbed laser power. Experiments with varying process parameters were performed to develop and validate an analytical model that predicts the hardness of printed AlSi10Mg parts. It was found that it is possible to tune the hardness of additively manufactured parts of AlSi10Mg in a range between 60 ± 9 HV0.5 and 100 ± 10 HV0.5 by adjusting the cooling rate during solidification with adapted process parameters.Item Open Access Comparison of in-process laser drying with furnace and vacuum drying to reduce moisture of AlSi10Mg powder processed in Laser Powder Bed Fusion(2024) Lubkowitz, Victor; Fayner, Leonie; Kramer, Steffen; Schulze, Volker; Zanger, FrederikIn most powder bed-based laser melting systems (PBF-LB), metal powders must be handled without inertization but in an air atmosphere for a short time, increasing the AlSi10Mg powder moisture and reducing the achievable component density. Consequently, different drying methods were investigated. Drying in a furnace with an inert atmosphere, using a vacuum to evaporate the water at low temperatures, and vaporizing moisture layerwise from the spreaded powder with a defocused, low-power laser beam as a further process step of the PBF-LB process. Therefore, four different moisturized powders, which were dried with different settings for the drying methods, are analyzed. All drying methods reduce the moisture content of the powder, with in-process drying being the most effective. Due to the oxide layer growth around the particles during furnace and vacuum drying, the achievable sample density after drying is worse. In-process drying with low energy density is the best option to reach a reduction of hydrogen pores and an increase of density.Item Open Access Shoulderless Friction Stir Welding : a low-force solid state keyhole joining technique for deep welding of labile structures(2021) Hossfeld, MaxThis paper reports on the possibility of performing Friction Stir Welding (FSW) without the usual immanent shoulder to enable FS processing to deep welding of narrow and labile structures and applications where backing is not possible. Requirements and prerequisites, advantages and limitations for Shoulderless Friction Stir Welding (SLFSW) are discussed and an industrial application of the joining technology is presented. For leaving the shoulder out, its central functions in FSW have to be transferred to the pin. The resulting tool design of SLFSW is comparably small and slim and so reduces contact area and effective lever and in turn forces and heat input during processing. SLFSW allows welding paths almost at the edge of components and enables a complete and gap-free joining while a deformation of overhanging structures can be avoided. Compared to standard FSW processes, force reductions of about 80–85 % and power reductions of about 75-80 % were found in this study for a 6.5 mm deep weld opening up additional potential for integration with other spindle processes like milling. The locally very limited process impact of SLFSW resulted in comparably low distortion with a part precision reached of +/- 0.05 mm.Item Open Access Friction and wear behavior of deep drawing tools using volatile lubricants injected through laser-drilled micro-holes(2021) Reichardt, Gerd; Henn, Manuel; Reichle, Paul; Umlauf, Georg; Riedmüller, Kim; Weber, Rudolf; Barz, Jakob; Liewald, Mathias; Graf, Thomas; Tovar, Günter E. M.In deep drawing processes, the use of lubricants is mandatory in order to prevent wear on tools and surface damage to the formed sheet metal components. Here, frequently used lubricants are synthetic and mineral oils, emulsions, and waxes. However, these conventional lubricants have to be applied to the sheet material prior to the forming operation and removed afterwards by cleaning processes. Additionally, the lubricants often contain substances that are harmful to the environment and to human health. To counteract these economic and ecological disadvantages, research is currently being conducted on a novel tribological system. For this, volatile media such as liquid carbon dioxide and gaseous nitrogen are being used, and are introduced directly into the friction zones between the tool and the sheet metal material during deep drawing under high pressure through special laser-drilled micro-holes. This paper covers the latest investigations and findings regarding the design of flow-optimized micro-holes, the laser drilling process, the friction characterization on tool radii, and the tool wear to be expected when using the lubrication medium CO2.Item Open Access Review on experimental and theoretical investigations of ultra-short pulsed laser ablation of metals with burst pulses(2021) Förster, Daniel J.; Jäggi, Beat; Michalowski, Andreas; Neuenschwander, BeatLaser processing with ultra-short double pulses has gained attraction since the beginning of the 2000s. In the last decade, pulse bursts consisting of multiple pulses with a delay of several 10 ns and less found their way into the area of micromachining of metals, opening up completely new process regimes and allowing an increase in the structuring rates and surface quality of machined samples. Several physical effects such as shielding or re-deposition of material have led to a new understanding of the related machining strategies and processing regimes. Results of both experimental and numerical investigations are placed into context for different time scales during laser processing. This review is dedicated to the fundamental physical phenomena taking place during burst processing and their respective effects on machining results of metals in the ultra-short pulse regime for delays ranging from several 100 fs to several microseconds. Furthermore, technical applications based on these effects are reviewed.Item Open Access Laserstrahlschweißen von Metallen mit unterschiedlichen thermophysikalischen Eigenschaften(München : utzverlag, 2020) Jarwitz, Michael; Graf, Thomas (Prof. Dr. phil. nat.)Im Rahmen dieser Arbeit wurden prozessangepasste Strategien für die gezielte Energieeinbringung beim Laserstrahlschweißen von Metallen mit unterschiedlichen thermophysikalischen Eigenschaften untersucht und entwickelt. Die Umsetzung wurde anhand der Beispiele des Laserstrahlschweißens von Nickelschaum an Nickelblech und des Laserstrahlschweißens von Aluminium-Kupfer-Mischverbindungen demosntriert.Item Open Access Influence of a closed-loop controlled laser metal wire deposition process of S Al 5356 on the quality of manufactured parts before and after subsequent machining(2021) Becker, Dina; Boley, Steffen; Eisseler, Rocco; Stehle, Thomas; Möhring, Hans-Christian; Onuseit, Volkher; Hoßfeld, Max; Graf, ThomasThis paper describes the interdependence of additive and subtractive manufacturing processes using the production of test components made from S Al 5356. To achieve the best possible part accuracy and a preferably small wall thickness already within the additive process, a closed loop process control was developed and applied. Subsequent machining processes were nonetheless required to give the components their final shape, but the amount of material in need of removal was minimised. The effort of minimising material removal strongly depended on the initial state of the component (wall thickness, wall thickness constancy, microstructure of the material and others) which was determined by the additive process. For this reason, knowledge of the correlations between generative parameters and component properties, as well as of the interdependency between the additive process and the subsequent machining process to tune the former to the latter was essential. To ascertain this behaviour, a suitable test part was designed to perform both additive processes using laser metal wire deposition with a closed loop control of the track height and subtractive processes using external and internal longitudinal turning with varied parameters. The so manufactured test parts were then used to qualify the material deposition and turning process by criteria like shape accuracy and surface quality.Item Open Access Supercritical melt flow in high-speed laser welding and its interdependence with the geometry of the keyhole and the melt pool(2024) Reinheimer, Eveline N.; Berger, Peter; Hagenlocher, Christian; Weber, Rudolf; Graf, ThomasThe advent of undercuts and humping limits the applicable speed of deep-penetration laser welding. Recent findings additionally show that a significant change of the keyhole’s shape is associated with the occurrence of undercuts. Considering that undercuts and humping are melt flow–induced defects, this leads to the question of how the geometry of the keyhole and the melt pool influence the melt flow and vice versa. In this work, the Froude number was used to characterize the melt flow around a keyhole. X-ray images of the keyhole and cross-sections of the weld were therefore used to determine the geometrical boundaries of the melt flow, to estimate the average melt velocity around the keyhole, and finally determine its Froude number. The flow around a cylindrically shaped keyhole was found to always be subcritical, whereas supercritical melt flow was observed around the elongated keyholes that are formed at higher welding speed. The findings may be interpreted in the sense that the elongation of the keyhole is a consequence of a supercritical stream of the melt flowing underneath and around the keyhole. This perception is consistent with the long-known experience that humping may be avoided by reducing the flow speed of the melt by widening the melt pool surrounding the keyhole (e.g., by means of beam shaping) and suggest a new explanation for the elongation of the keyhole at increased welding speed.