Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
12 results
Search Results
Item Open Access Simulation study on single-lip deep hole drilling using design of experiments(2021) Fandino, Daniel; Guski, Vinzenz; Wegert, Robert; Möhring, Hans-Christian; Schmauder, SiegfriedSingle-lip deep hole drilling (SLD) is characterized by a high surface quality and compressive residual stress in the subsurface of the drill hole. These properties are strongly dependent on the cutting parameters of the SLD process and the actual geometry of the insert and the guide pads. In the present work, full 3D FE simulations of the SLD process were carried out to analyze the thermo-mechanical as-is state in the drilling contact zone by evaluating the feed force, the temperature, as well as the residual stress in the drill hole subsurface. An extensive simulation study was conducted on the effect of the process parameters on the properties using design of experiments (DoE). For the simulations, the Johnson-Cook (JC) constitutive law and the element elimination technique (EET) were applied to represent the material behavior of the workpiece, including chip formation. In-process measurements as well as results from the hole-drilling method to determine residual stresses were conducted to verify the numerical results. By means of DoE and analysis of variance (ANOVA), regression models were developed to describe the effect of the feed rate, cutting speed, and guide pad height on the temperature, feed force, and residual stress in the subsurface.Item Open Access Evaluation of methods for measuring tool-chip contact length in wet machining using different approaches (microtextured tool, in-situ visualization and restricted contact tool)(2022) Ellersiek, Lars; Menze, Christian; Sauer, Florian; Denkena, Berend; Möhring, Hans-Christian; Schulze, VolkerThe contact length is one of the most important factors to evaluate the chip formation process and the mechanical loads in metal cutting. Over the years, several methods to identify the contact length were developed. However, especially for wet cutting processes the determination of the contact length is still challenging. In this paper, three methods to identify the contact length for dry and wet processes in cutting of Ti6Al4V and AISI4140 + QT are presented, discussed and analyzed. The first approach uses tools with a microtextured rake face. By evaluating the microstructures on the chip, a new method to identify the contact length is established. The second approach applies high speed recordings to identify the contact length. The challenge is thereby the application of high-speed recordings under wet conditions. In the third approach, tools with restricted contact length are used. It is shown that with all three methods the contact length is reduced using metal working fluid.Item Open Access SmartLab vernetzt Produktionsmaschinen : Aufbau einer digitalen Prozesskette in einer bestehenden Produktionsumgebung(2023) Schneider, Matthias; Meier, Veronika; Stehle, Thomas; Möhring, Hans-ChristianItem Open Access Validation of the manufacturing Methodology of prestressed fiber-reinforced polymer concrete by the variation of process parameters(2023) Engert, Michelle; Werkle, Kim Torben; Wegner, Robert; Born, Larissa; Gresser, Götz T.; Möhring, Hans-ChristianPolymer concrete has proved to be advantageous in machine building for many years thanks to its excellent damping properties. Until now, its use was limited to machine beds due to its comparatively low tensile strength. Its use in moving structural components has not been possible until now. Recent research results have shown that this challenge can be met by integrating prestressed carbon fibers. Until now, the production of samples out of prestressed fiber-reinforced polymer concrete has been carried out according to fixed specifications. It is not yet clear whether these specifications are suitable to fully exploit the potential of the material. Samples manufactured to these specifications show at least a large scatter in bending stiffness. Within the scope of this paper, the existing manufacturing process is validated by the variation of process steps. Specifically, this involved the use of a shaker, variation of the dwell time in the mold, variation of the resin content, and the procedure for impregnating the fibers. The characterization of the samples showed that the scatter could only be reduced by increasing the dwell time. However, this leads to a decrease in bending stiffness and, thus, is not suitable for further improvement of the novel material.Item Open Access Development of a multi-sensor concept for real-time temperature measurement at the cutting insert of a single-lip deep hole drilling tool(2022) Ramme, Johannes; Wegert, Robert; Guski, Vinzenz; Schmauder, Siegfried; Möhring, Hans-ChristianThe mechanical energy resulting from cutting processes is turned almost completely in thermal energy, which encourages thermal procedures, such as diffusion, leading to higher wear in the cutting tool and thus to higher temperatures. Furthermore, high temperatures influence the properties of the marginal zones in the workpiece. In this presented work, the in-process temperature of a cutting insert during single-lip deep hole drilling (SLD) is investigated. Therefore, a sensor-integrated tool with resistance temperature detectors (RTD) placed beneath the cutting insert is developed. First, the thermal properties of the cutting insert are adjusted to fit the assembled tool. Afterwards, a CEL-Simulation is obtained to examine the temperature distribution at the cutting edge of the SLD-tool. The temperatures calculated by simulation can be compared to the in-process temperatures of the sensor integrated tool. Because of the usage of a cooling lubricant, simulated temperatures can be varied with a factor to fit the experimentally measured temperature curves. The highest temperature during the process appears at the outer edge of the cutting insert. By knowing the thermal properties, the maximum process temperatures for the deep hole drilling operation are to be calculated. The results represent a contribution to an interdisciplinary research project “Surface Conditioning in Machining Processes” (SPP 2086) of the German Research Foundation (DFG).Item Open Access Determination of the shear angle in the orthogonal cutting process(2022) Storchak, Michael; Stehle, Thomas; Möhring, Hans-ChristianDetermination of the shear angle by experimental and analytical methods, as well as by numerical simulation, is presented. Experimental determination of the shear angle was performed by analyzing the chip roots obtained by the method of cutting process quick stop through purposeful fracture of the workpiece in the area surrounding the primary cutting zone. The analytical determination of the shear angle was carried out using the chip compression ratio and was based on the principle of a potential energy minimum. Measurement of the shear angle in the numerical simulation of orthogonal cutting was performed using the strain rate pattern of the machined material at the selected simulation moment. It was analyzed how the parameters of the Johnson-Cook constitutive equation and the friction model affect the shear angle value. The parameters with a predominant effect on the shear angle were determined. Then the generalized values of these parameters were established with a software algorithm based on identifying the intersection of the constitutive equation parameter sets. The use of generalized parameters provided the largest deviation between experimental and simulated shear angle values from 9% to 18% and between simulated and analytically calculated shear angle values from 7% to 12%.Item Open Access Flow visualisation and evaluation studies on metalworking fluid applications in manufacturing processes : methods and results(2023) Fritsching, Udo; Buss, Lizoel; Tonn, Teresa; Schumski, Lukas; Gakovi, Jurgen; Hatscher, Johnson David; Sölter, Jens; Avila, Kerstin; Karpuschewski, Bernhard; Gerken, Julian Frederic; Wolf, Tobias; Biermann, Dirk; Menze, Christian; Möhring, Hans-Christian; Tchoupe, Elio; Heidemanns, Lukas; Herrig, Tim; Klink, Andreas; Nabbout, Kaissar; Sommerfeld, Martin; Luther, Fabian; Schaarschmidt, Ingo; Schubert, Andreas; Richter, MarkusMetalworking operations rely on the successful application of metalworking fluids (MWFs) for effective and efficient operation. Processes such as grinding or drilling often require the use of MWFs for cooling, lubrication, and chip removal. Electrochemical machining processes require electrolyte flow to operate. However, in those machining operations, a fundamental understanding of the mode of action of MWF is lacking due to the unknown flow dynamics and its interaction with the material removal during the process. Important information on the behaviour of MWFs during machining can be obtained from specific experimental flow visualisation studies. In this paper, promising flow visualisation analysis techniques applied to exemplary machining processes (grinding, sawing, drilling, and electrochemical machining) are presented and discussed. Shadowgraph imaging and flow measurements, e.g., particle image velocimetry, allow the identification of typical flow and MWF operating regimes in the different machining processes. Based on the identification of these regimes, efficient machining parameters and MWF applications can be derived. In addition, detailed experimental analyses of MWFs provide essential data for the input and validation of model development and numerical simulations within the Priority Programme SPP 2231 FluSimPro.Item Open Access Einsatz von KI bei der Prozessvorhersage für Bandsägen : Einsatz von künstlicher Intelligenz zur Vorhersage von Prozesskräften beim Bandsägen(2023) Tandler, Tobias; Hirth, Thomas; Eisseler, Rocco; Stehle, Thomas; Möhring, Hans-ChristianItem Open Access Assessment of the heat transfer conditions in the cavity of a rotating circular saw(2024) Stegmann, Jan; Baumert, Moritz; Kabelac, Stephan; Menze, Christian; Ramme, Johannes; Möhring, Hans-ChristianTo improve machining processes concerning the usage of lubricants, knowledge of the thermo-mechanical and thermo-fluid interactions at the cutting zone is of great importance. This study focuses on the description of the convective heat transfer which occurs during circular sawing when the lubricant is provided via an internal coolant supply. The highly complex flow field inside the cavity of the sawing process is separated into two distinct flow forms, an impingement and a channel flow. With the aid of experimental and numerical studies, the heat transfer characteristics of these two flow forms have been examined for water and a lubricant used in the circular sawing process. Studies have been conducted over a wide range of Reynolds numbers (impingement flow: 2×103Item Open Access Cutting tool condition monitoring using eigenfaces : tool wear monitoring in milling(2022) König, Wolfgang; Möhring, Hans-ChristianEffective monitoring of the tool wear condition within a machining process can be very challenging. Depending on the sensors used, often only a part of the relevant wear information can be detected. In the case of milling processes data acquisition is made even more difficult by the fact that the process working point is inaccessible for sensor applications due to the physical tool, the machining process itself, the chipping and used cooling-lubricants. By using a variety of sensors and different measuring principles, sensor data fusion strategies can counteract this problem. An approach to this is the eigenface algorithm. This approach, a face recognition technique, is tested for its suitability on tool condition monitoring in milling processes by using multi-sensor process data.