Universität Stuttgart
Permanent URI for this communityhttps://elib.uni-stuttgart.de/handle/11682/1
Browse
5 results
Search Results
Item Open Access Tuning the hardness of produced parts by adjusting the cooling rate during laser-based powder bed fusion of AlSi10Mg by adapting the process parameters(2022) Leis, Artur; Traunecker, David; Weber, Rudolf; Graf, ThomasThe mechanical properties of parts produced by laser-based powder bed fusion (LPBF) are mainly determined by the grain structure in the material, which is governed by the cooling rate during solidification. This cooling rate strongly depends on the scan velocity and the absorbed laser power. Experiments with varying process parameters were performed to develop and validate an analytical model that predicts the hardness of printed AlSi10Mg parts. It was found that it is possible to tune the hardness of additively manufactured parts of AlSi10Mg in a range between 60 ± 9 HV0.5 and 100 ± 10 HV0.5 by adjusting the cooling rate during solidification with adapted process parameters.Item Open Access Friction and wear behavior of deep drawing tools using volatile lubricants injected through laser-drilled micro-holes(2021) Reichardt, Gerd; Henn, Manuel; Reichle, Paul; Umlauf, Georg; Riedmüller, Kim; Weber, Rudolf; Barz, Jakob; Liewald, Mathias; Graf, Thomas; Tovar, Günter E. M.In deep drawing processes, the use of lubricants is mandatory in order to prevent wear on tools and surface damage to the formed sheet metal components. Here, frequently used lubricants are synthetic and mineral oils, emulsions, and waxes. However, these conventional lubricants have to be applied to the sheet material prior to the forming operation and removed afterwards by cleaning processes. Additionally, the lubricants often contain substances that are harmful to the environment and to human health. To counteract these economic and ecological disadvantages, research is currently being conducted on a novel tribological system. For this, volatile media such as liquid carbon dioxide and gaseous nitrogen are being used, and are introduced directly into the friction zones between the tool and the sheet metal material during deep drawing under high pressure through special laser-drilled micro-holes. This paper covers the latest investigations and findings regarding the design of flow-optimized micro-holes, the laser drilling process, the friction characterization on tool radii, and the tool wear to be expected when using the lubrication medium CO2.Item Open Access Supercritical melt flow in high-speed laser welding and its interdependence with the geometry of the keyhole and the melt pool(2024) Reinheimer, Eveline N.; Berger, Peter; Hagenlocher, Christian; Weber, Rudolf; Graf, ThomasThe advent of undercuts and humping limits the applicable speed of deep-penetration laser welding. Recent findings additionally show that a significant change of the keyhole’s shape is associated with the occurrence of undercuts. Considering that undercuts and humping are melt flow–induced defects, this leads to the question of how the geometry of the keyhole and the melt pool influence the melt flow and vice versa. In this work, the Froude number was used to characterize the melt flow around a keyhole. X-ray images of the keyhole and cross-sections of the weld were therefore used to determine the geometrical boundaries of the melt flow, to estimate the average melt velocity around the keyhole, and finally determine its Froude number. The flow around a cylindrically shaped keyhole was found to always be subcritical, whereas supercritical melt flow was observed around the elongated keyholes that are formed at higher welding speed. The findings may be interpreted in the sense that the elongation of the keyhole is a consequence of a supercritical stream of the melt flowing underneath and around the keyhole. This perception is consistent with the long-known experience that humping may be avoided by reducing the flow speed of the melt by widening the melt pool surrounding the keyhole (e.g., by means of beam shaping) and suggest a new explanation for the elongation of the keyhole at increased welding speed.Item Open Access High-speed single-frame polarimeter for thermal radiation to measure the 3D geometry of hot metal surfaces(2024) Sawannia, Michael; Berger, Peter; Weber, Rudolf; Hagenlocher, Christian; Graf, ThomasThe 3D geometry of the interaction zone in laser material processing is of major importance as it defines the absorption of the laser beam and may influence the hydrodynamics of the process. With the aim of measuring this geometry, which typically changes with frequencies in the order of 10 kHz, a single-frame polarimeter with acquisition rates of up to 75 kHz is presented in this work. It simultaneously records four images of the thermal process emission, through four linear polarizers with different orientations. The formulae required for the reconstruction of the 3D geometry from these images are derived and validated on an example of a heated steel sphere. The reconstructed geometry was found to be in good agreement with the examined sphere. An experimental example is also given of the application of this technology to geometry measurement of a highly dynamic laser cutting front at a framerate of 75 kHz.Item Open Access Adjustment of the geometries of the cutting front and the kerf by means of beam shaping to maximize the speed of laser cutting(2023) Lind, Jannik; Hagenlocher, Christian; Weckenmann, Niklas; Blazquez-Sanchez, David; Weber, Rudolf; Graf, ThomasThe shape of the laser beam used for fusion cutting significantly influences the geometry of both the cutting front and the cutting kerf. The angle of the cutting front in turn impacts the local absorptivity, while the width of the kerf defines the amount of material, which has to be molten. The kerf’s geometry therefore determines the maximum possible cutting speed at which a successful cut is feasible with a given available laser power. The absorptivity, the width of the kerf, and the maximum possible cutting speed can be estimated from a simple model considering the conservation of energy and rough geometrical approximations. In order to verify the prediction of the model, the geometry of the cutting front and kerf resulting from different processing conditions was observed by means of online high-speed X-ray diagnostics. The geometry of the interaction zone was recorded with a framerate of 1000 Hz during fusion cutting of 10-mm-thick samples of stainless steel. Comparing the results obtained with different shapes of the laser beam, it was found that the absorptivity is increased when the beam’s longitudinal cross-section (parallel to the feed) is enlarged. Reducing the width of the beam in the transversal direction normal to the feed reduces the cross-sectional area of the cutting kerf. The findings show a good agreement with the geometric model which enabled the prediction of the absorptivity and the cross-sectional area of the cutting kerf and hence allows to reliably estimate the maximum cutting speed for different shapes of the laser beam, laser power, and sheet thicknesses.