07 Fakultät Konstruktions-, Produktions- und Fahrzeugtechnik
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/8
Browse
36 results
Search Results
Item Open Access Local laser heat treatment of AlSi10Mg as-built parts produced by Laser Powder Bed Fusion(2024) Kramer, Steffen; Jarwitz, Michael; Schulze, Volker; Zanger, FrederikToday, complex structural components for lightweight applications are frequently manufactured by laser powder bed fusion (PBF-LB), often using aluminum alloys such as AlSi10Mg. However, the application of cyclic load cases can be challenging as PBF-LB produced AlSi10Mg parts typically have low ductility and corresponding brittle failure behavior in the as-built condition. Therefore, this paper presents investigations on the feasibility of a laser heat treatment of PBF-LB produced AlSi10Mg parts to locally increase the ductility and decrease the hardness in critical areas. Potential heat treatment process parameters were derived theoretically based on the temperature fields in the material calculated assuming three-dimensional heat conduction and a moving heat source. PBF-LB produced specimens were then laser heat treated at varying laser power and scan speed. Hardness measurements on metallographic cross sections showed hardness reductions of over 35 % without inducing hydrogen pore growth.Item Open Access General mathematical model for the period chirp in interference lithography(2023) Bienert, Florian; Graf, Thomas; Abdou Ahmed, MarwanItem Open Access Influence of geometry variations during pyrometric temperature measurement in laser material processing(2024) Traunecker, David; Jarwitz, Michael; Michalowski, AndreasItem Open Access Process limits for percussion drilling of stainless steel with ultrashort laser pulses at high average powers(2022) Brinkmeier, David; Holder, Daniel; Loescher, André; Röcker, Christoph; Förster, Daniel J.; Onuseit, Volkher; Weber, Rudolf; Abdou Ahmed, Marwan; Graf, ThomasThe availability of commercial ultrafast lasers reaching into the kW power level offers promising potential for high-volume manufacturing applications. Exploiting the available average power is challenging due to process limits imposed by particle shielding, ambient atmosphere breakdown, and heat accumulation effects. We experimentally confirm the validity of a simple thermal model, which can be used for the estimation of a critical heat accumulation threshold for percussion drilling of AISI 304 steel. The limits are summarized in a processing map, which provides selection criteria for process parameters and suitable lasers. The results emphasize the need for process parallelization.Item Open Access Stream finishing of additively manufactured AlSi10Mg PBF-LB parts: influence on surface quality and fatigue behaviour(2024) Wexel, Helena; Kramer, Steffen; Schubert, Johannes; Schulze, Volker; Zanger, FrederikItem Open Access Tuning the hardness of produced parts by adjusting the cooling rate during laser-based powder bed fusion of AlSi10Mg by adapting the process parameters(2022) Leis, Artur; Traunecker, David; Weber, Rudolf; Graf, ThomasThe mechanical properties of parts produced by laser-based powder bed fusion (LPBF) are mainly determined by the grain structure in the material, which is governed by the cooling rate during solidification. This cooling rate strongly depends on the scan velocity and the absorbed laser power. Experiments with varying process parameters were performed to develop and validate an analytical model that predicts the hardness of printed AlSi10Mg parts. It was found that it is possible to tune the hardness of additively manufactured parts of AlSi10Mg in a range between 60 ± 9 HV0.5 and 100 ± 10 HV0.5 by adjusting the cooling rate during solidification with adapted process parameters.Item Open Access Comparison of in-process laser drying with furnace and vacuum drying to reduce moisture of AlSi10Mg powder processed in Laser Powder Bed Fusion(2024) Lubkowitz, Victor; Fayner, Leonie; Kramer, Steffen; Schulze, Volker; Zanger, FrederikIn most powder bed-based laser melting systems (PBF-LB), metal powders must be handled without inertization but in an air atmosphere for a short time, increasing the AlSi10Mg powder moisture and reducing the achievable component density. Consequently, different drying methods were investigated. Drying in a furnace with an inert atmosphere, using a vacuum to evaporate the water at low temperatures, and vaporizing moisture layerwise from the spreaded powder with a defocused, low-power laser beam as a further process step of the PBF-LB process. Therefore, four different moisturized powders, which were dried with different settings for the drying methods, are analyzed. All drying methods reduce the moisture content of the powder, with in-process drying being the most effective. Due to the oxide layer growth around the particles during furnace and vacuum drying, the achievable sample density after drying is worse. In-process drying with low energy density is the best option to reach a reduction of hydrogen pores and an increase of density.Item Open Access Theoretical investigation on the elimination of the period chirp by deliberate substrate deformations(2022) Bienert, Florian; Graf, Thomas; Abdou Ahmed, MarwanWe present a theoretical investigation on the approach of deliberately bending the substrate during the exposure within laser interference lithography to compensate for the period chirp. It is shown that the yet undiscovered function of the surface geometry, necessary to achieve the zero-chirp case (i.e. having a perfectly constant period over the whole substrate) is determined by a first-order differential equation. As the direct analytical solution of this differential equation is difficult, a numerical approach is developed, based on the optimization of pre-defined functions towards the unknown analytical solution of the differential equation by means of a Nelder-Mead simplex algorithm. By applying this method to a concrete example, we show that an off-center placement of the substrate with respect to the point sources is advantageous both in terms of achievable period and substrate curvature and that a fourth-order polynomial can greatly satisfy the differential equation leading to a root-mean-square deviation of only 1.4 pm with respect to the targeted period of 610 nm.Item Open Access Intra-cavity wavelength multiplexing of high-brightness thin-disk laser beams(2022) Boubekraoui, Ayoub; Beirow, Frieder; Graf, Thomas; Abdou Ahmed, MarwanWe report on the first demonstration of an intra-cavity spectral beam combining of two fundamental-mode laser beams generated by a dual Yb:YAG thin-disk resonator. The two thin-disk lasers (TDLs) were operated at the two slightly different wavelengths of 1028 nm and 1032 nm. A resonant diffraction grating waveguide structure was used as common spectral stabilizer and combiner. An average power exceeding 200 W with close to diffraction-limited beam quality (M2<1.3) was obtained with the presented approach.Item Open Access Different coupling mechanisms for a novel modular plate in acetabular fractures : a comparison using a laparoscopic model(2024) Menger, Maximilian M.; Herath, Steven C.; Ellmerer, Andreas E.; Trulson, Alexander; Hoßfeld, Max; Leis, Artur; Ollig, Annika; Histing, Tina; Küper, Markus A.; Audretsch, Christof K.Introduction: Acetabular fractures are among the most challenging injuries in traumatology. The complex anatomy usually requires extensive surgical approaches baring the risk for iatrogenic damage to surrounding neurovascular structures. As a viable alternative, minimally invasive endoscopic techniques have emerged during the recent years. This paper reports on the feasibility of different coupling mechanisms for a novel suprapectineal plate especially designed for minimally invasive acetabular surgery. Methods: A total number of 34 participants contributed to the present study, who differed in their arthroscopic and surgical experience. A laparoscopic model was used to compare four different coupling mechanisms by the number of failed attempts, the time required for plate fixation, the influence of surgical experience as well as the learning success for each individual coupling mechanism. Moreover, the feasibility of each mechanism was evaluated by a questionnaire. Results: The results demonstrate that plates employing grooved and pressure-sliding coupling mechanisms exhibit fewer failed attempts and reduce trial times, especially in contrast to sole sliding mechanisms. Furthermore, our study revealed that proficiency in endoscopic procedures significantly influenced the outcome. Notably, the subjective evaluation of the participants show that the pressure base and pressure-slide base plate designs are the most supportive and feasible designs. Conclusions: In summary, the present study evaluates for the first-time different plate and coupling designs for minimal-invasive surgery, indicating a superior feasibility for plates with a grooved and pressure-sliding mechanism.