03 Fakultät Chemie
Permanent URI for this collectionhttps://elib.uni-stuttgart.de/handle/11682/4
Browse
6 results
Search Results
Item Open Access Chitin/cellulose blend fibers prepared by wet and dry‐wet spinning(2020) Ota, Antje; Beyer, Ronald; Hageroth, Ulrich; Müller, Alexandra; Tomasic, Patricija; Hermanutz, Frank; Buchmeiser, Michael R.We describe the wet and dry‐wet spinning of multifilament cellulosic composite fibers, namely chitin/cellulose fibers. The direct solution process for the two biopolymers based on an ionic liquid as solvent represents an environmentally friendly and alternative technology to the industrially applied viscose and lyocell process. Both cellulose and chitin possess good solubility in 1‐ethyl‐3‐methylimidazolium propionate ([C2C1Im][OPr]) and were spun into multifilament composite fibers. Moreover, for the first time, pure chitin multifilament fibers were obtained by dry‐wet spinning. The effect of chitin addition on the filament properties was investigated and evaluated by microscopic, spectroscopic, and mechanical analyses.Item Open Access Reversible N‐heterocyclic carbene‐induced α‐H abstraction in Tungsten(VI) imido dialkyl dialkoxide complexes(2020) Musso, Janis V.; Benedikter, Mathis J.; Wang, Dongren; Frey, Wolfgang; Altmann, Hagen J.; Buchmeiser, Michael R.The first reversible N‐heterocyclic carbene (NHC) induced α‐H abstraction in tungsten(VI) imido‐dialkyl dialkoxide complexes is reported. Treatment of W(NAr)(CH2Ph)2(OtBu)2 (Ar=2,6‐dichlorophenyl, 2,6‐dimethylphenyl, 2,6‐diisopropylphenyl) with different NHCs leads to the formation of complexes of the type W(NAr)(CHPh)(NHC)(CH2Ph)(OtBu) in excellent isolated yields of up to 96 %. The highly unusual release of the tert‐butoxide ligand as tBuOH in the course of the reaction was observed. The formed alkylidene complexes and tBuOH are in an equilibrium with the NHC and the dialkyl complexes. Reaction kinetics were monitored by 1H NMR spectroscopy. A correlation between the steric and electronic properties of the NHC and the reaction rates was observed. Kinetics of a deuterium‐labeled complex in comparison to its non‐deuterated counterpart revealed the presence of a strong primary kinetic isotope effect (KIE) of 4.2, indicating that α‐H abstraction is the rate‐determining step (RDS) of the reaction.Item Open Access Asymmetric Rh diene catalysis under confinement : isoxazole ring‐contraction in mesoporous solids(2024) Marshall, Max; Dilruba, Zarfishan; Beurer, Ann‐Katrin; Bieck, Kira; Emmerling, Sebastian; Markus, Felix; Vogler, Charlotte; Ziegler, Felix; Fuhrer, Marina; Liu, Sherri S. Y.; Kousik, Shravan R.; Frey, Wolfgang; Traa, Yvonne; Bruckner, Johanna R.; Plietker, Bernd; Buchmeiser, Michael R.; Ludwigs, Sabine; Naumann, Stefan; Atanasova, Petia; Lotsch, Bettina V.; Zens, Anna; Laschat, SabineCovalent immobilization of chiral dienes in mesoporous solids for asymmetric heterogeneous catalysis is highly attractive. In order to study confinement effects in bimolecular vs monomolecular reactions, a series of pseudo‐C2‐symmetrical tetrahydropentalenes was synthesized and immobilized via click reaction on different mesoporous solids (silica, carbon, covalent organic frameworks) and compared with homogeneous conditions. Two types of Rh‐catalyzed reactions were studied: (a) bimolecular nucleophilic 1,2‐additions of phenylboroxine to N‐tosylimine and (b) monomolecular isomerization of isoxazole to 2H‐azirne. Polar support materials performed better than non‐polar ones. Under confinement, bimolecular reactions showed decreased yields, whereas yields in monomolecular reactions were only little affected. Regarding enantioselectivity the opposite trend was observed, i. e. effective enantiocontrol for bimolecular reactions but only little control for monomolecular reactions was found.Item Open Access Method of manufacturing structural, optically transparent glass fiber-reinforced polymers (tGFRP) using infusion techniques with epoxy resin systems and E-glass fabrics(2023) Heudorfer, Klaus; Bauer, Johannes; Caydamli, Yavuz; Gompf, Bruno; Take, Jens; Buchmeiser, Michael R.; Middendorf, PeterRecently, fiber-reinforced, epoxy-based, optically transparent composites were successfully produced using resin transfer molding (RTM) techniques. Generally, the production of structural, optically transparent composites is challenging since it requires the combination of a very smooth mold surface with a sufficient control of resin flow that leads to no visible voids. Furthermore, it requires a minimum deviation of the refractive indices (RIs) of the matrix polymer and the reinforcement fibers. Here, a new mold design is described and three plates of optically transparent glass fiber-reinforced polymers (tGFRP) with reproducible properties as well as high fiber volume fractions were produced using the RTM process and in situ polymerization of an epoxy resin system enclosing E-glass fiber textiles. Their mechanical (flexural), microstructural (fiber volume fraction, surface roughness, etc.), thermal (DSC, TGA, etc.), and optical (dispersion curves of glass fibers and polymer as well as transmission over visible spectra curves of the tGFRP at varying tempering states) properties were evaluated. The research showed improved surface quality and good transmission data for samples manufactured by a new Optical-RTM setup compared to a standard RTM mold. The maximum transmission was reported to be ≈74%. In addition, no detectable voids were found in these samples. Furthermore, a flexural modulus of 23.49 ± 0.64 GPa was achieved for the Optical-RTM samples having a fiber volume fraction of ≈42%.Item Open Access Dual catalysis with an N‐heterocyclic carbene and a Lewis acid : thermally latent precatalyst for the polymerization of ε‐caprolactam(2020) Altmann, Hagen J.; Steinmann, Mark; Elser, Iris; Benedikter, Mathis J.; Naumann, Stefan; Buchmeiser, Michael R.So far, the earlier reported strong correlation between basicity of an N‐heterocyclic carbene (NHC) and its reactivity in poly(ε‐caprolactam) (PA6) synthesis resulted in a substantial limitation of applicable carbenes. Here, to overcome this issue, 1,3‐dimethylimidazolium‐2‐carboxylate, an easily accessible, air and moisture‐stable NHC, was applied as thermally latent initiator. In order to compensate for its low basicity, reactivity was enhanced by the addition of both a Lewis acid and an activator to ease the initial polymerization step. The resulting mixtures of ε‐caprolactam, the CO2‐protected NHC, a Lewis acid and N‐acylazepan‐2‐one constitute homogeneous, thermally fully latent “single‐component” blends for the anionic polymerization‐based synthesis of PA6. They can be stored both in the liquid and solid state for days and months, respectively, without any loss in activity. The role of the Lewis acid as well as technical implications of the prolonged pot‐times are discussed.Item Open Access Melt spinning of propylene carbonate‐plasticized poly(acrylonitrile)‐co‐poly(methyl acrylate)(2020) König, Simon; Kreis, Philipp; Reinders, Leonie; Beyer, Ronald; Wego, Andreas; Herbert, Christian; Steinmann, Mark; Frank, Erik; Buchmeiser, Michael R.The primary use of poly(acrylonitrile) (PAN) fibers, commonly referred to as acrylic fibers, is in textile applications like clothing, furniture, carpets, and awnings. All commercially available PAN fibers are processed by solution spinning; however, alternative, more cost‐effective processes like melt spinning are still highly desired. Here, the melt spinning of PAN‐co‐poly(methyl acrylate) (PMA) plasticized with propylene carbonate (PC) at 175°C is reported. The use of methyl acrylate (MA) as comonomer and PC as an external plasticizer renders the approach a combination of internal and external plasticization. Various mixtures of PAN and PC used in this work were examined by rheology, subjected to melt spinning, followed by discontinuous and continuous washing, respectively. The best fibers were derived from a PAN‐co‐PMA copolymer containing 8.1 mol‐% of MA having a number‐average molecular weight Mn of 34 000 g/mol, spun in the presence of 22.5 wt.‐% of PC. The resulting fibers were analyzed by scanning electron microscopy and wide‐angle X‐ray scattering (WAXS), and were subjected to mechanical testing.